Continue press and hold the + button. Continue to hold both buttons until the LED starts to to hold both buttons until the LED starts to blink ( approximately 5 seconds) . Release blink ( approximately 5 seconds) . Release both buttons while the LED is blinking. both buttons while the LED is blinking. The LED will blink two times and then The LED will blink two times and then remain on to confirm you are in remain on to confirm you are in programming mode. Go to Step 2 programming mode. Go to St

All implied warranties of merchantability and/ or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other

The transmitter to attach the unit to a code is retained in permanent memory and will not be sun visor. If the clip is lost during battery replacement. To replace the used, slide it into the batteries, remove the back of the case with a small recess provided on the screwdriver. Carefully slip the batteries out of the back of the transmitter holders and replace with fresh CR2032 3- volt batteries. case until the snaps on the case fit around the clip. The “+ ” on the batteries must point away from

Write the code that you matched from your transmitter or receiver in the grids below. 1 2 3 4 5 6 7 8 9 + / On BUTTON Zero BUTTON - / Off BUTTON - PUT THE TRANSMITTER IN PROGRAM MODE 1. First, press and hold the + 1a. First, press and hold the - button. The Red LED will turn on. Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons

In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product. This warranty gives you specific legal rights. Warranty effective after July 24, 2002. WARNING Unexpected door operations can cause personal injury or property damage. This device complies with Part 15 of the FCC Rules and with R

The LED will blink off once and then remain on. Go to Step 3. .. - ENTER YOUR 9 DIGIT CODE 3. Enter the 9- digit code from the table pressing the buttons that correspond with the grid above. (If your block has 8 switches use the + button in the 9th position) Go to Step 4. .. 4. After the 9- digit code is entered, the LED will blink twice to confirm a valid code and remain off. 5. Repeat the procedure for the remaining buttons. INSTRUCTIONS FOR USE WITH AN ALLSTAR SMART RECEIVER When using the Al

Put the transmitter in program mode. controlled devices such as a garage door opener, 2. Select the button you wish to use. with a single transmitter. 3. Enter your 9 digit code. Follow these simple instructions. Please read the instructions completely before starting. Further instructions are available at INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS Select the block of switches below that best matches the one in the transmitter or receiver that you are replacing. *The grids display an EXAMPLE usin

Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option. This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary maintenance) , labor charges for dismantling or reinstalling a repaired or r

controlled devices such as a garage door opener, 2. Select the button you wish to use. with a single transmitter. 3. Enter your 9 digit code. Follow these simple instructions. Please read the instructions completely before starting. Further instructions are available at INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS Select the block of switches below that best matches the one in the transmitter or receiver that you are replacing. *The grids display an EXAMPLE using the code shown on the switches to t

Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons until the LED starts to to hold both buttons until the LED starts to blink ( approximately 5 seconds) . Release blink ( approximately 5 seconds) . Release both buttons while the LED is blinking. both buttons while the LED is blinking. The LED will blink two times and then The LE