• LOCATE CONTROL PUSHBUTTONS WITHIN SIGHT OF THE DOOR AND AWAY FROM THE MOVING PARTS OF THE DOOR. INSTALL ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL PUSHBUTTON IN A PROMINENT LOCATION. • REMOVE ALL ROPES AND REMOVE OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR. • THE IMPORTANT SAFEGUARDS AND INSTRUCTIONS IN THIS MANUAL CANNOT COVER ALL POSSIBLE CONDITIONS AND SITUATIONS. IT MUST BE UNDERSTOOD THAT COMMON SENSE AND CAUTION MUST BE EXERCISED BY THE PERSON(S) INSTALLING, MAINTAINING

Follow the directions on the next page for proper Transmitter/Receiver Coding! 733 Rotary Switch selects door A, B or C Slide Switch selects door A, B or C 8833C-OCS Rotary Switch selects door 1, 2, 3, ... or 9 639 Combination of both Rotary Switches selects door Examples: A1, B7, C9, etc. 831 STOP CLOSE OPEN 8833-OCS STOP CLOSE OPEN 535 COMMERCIAL TRANSMITTER MODELS Page 3 of 4 P/N 107343 Rev D The information below indicates how to set the coding switches in the various transmitters and receiv

This is accomplished by setting the selector switch on the transmitter to either 1, 2, 3, 4, 5, 6, 7, 8 or 9 and setting the #7 and #8 coding switches in the 831 receiver. Start coding by exactly matching all 8 code switches in the transmitter and receivers. The code switches may be set in any random pattern of +, 0 and - positions. Next, in receiver 1, set code switch #7 to + and code switch #8 +; In receiver 2, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the

Some models are designed to operate multiple receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. • ALLSTAR TRANSMITTERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRIC

Start coding by exactly matching all 8 code switches in the transmitter and receiver. Next, in receiver A1, set code switch #6 to +, set code switch #7 to + and code switch #8 to +; In receiver A2, set code switch #6 to +, set code switch #7 to + and code switch #8 to 0. Continue setting the codes in the 831 receivers, using both tables shown above. TRANSMITTER A-B-C Selector Switch Position RECEIVER Coding Switch #6 A + B 0 C - TRANSMITTER 1 - 9 Selector Switch Position 831 RECEIVER Code Switch

Some models are designed to operate multiple receivers. A selector switch on the Transmitter determines which door will be controlled in a multi-door installation. The Receiver is connected to the commercial operator in the same manner as a 3-button station and provides open, close and stop functions via radio control. • ALLSTAR TRANSMITTERS ARE INTENDED FOR USE WITH COMMERCIAL DOOR OPERATORS ONLY. DO NOT USE FOR ANY OTHER PURPOSE. DO NOT MODIFY IN ANY MANNER. • CHECK LOCAL BUILDING AND ELECTRIC

Check the power connections to the receiver. There must be at least 20 VAC at the receiver power connections. (If a 24V system). Review the code switch and the selector switch settings then reprogram the receiver.. Try a different code switch setting. Check the antenna installation. Wait one minute for the receiver to “warm-up”. Check battery in transmitter. RECEIVER “CLICKS” WHEN ANY TRANSMITTER BUTTON IS PUSHED, BUT NOTHING ELSE HAPPENS. Check the wire & connections in the STOP circuit. Refer

8 switches w/ + 0 - WARNING Disconnect power to operator before any installation or repair. Follow all instructions provided by the manufacturer of your operator. After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. However, environmental conditions and the location of the transmitter and receiver will affect distance.

Next, button. The Red LED will turn on. Next, while continuing to hold the + button, while continuing to hold the - button, press and hold the - button. Continue press and hold the + button. Continue to hold both buttons until the LED starts to to hold both buttons until the LED starts to blink ( approximately 5 seconds) . Release blink ( approximately 5 seconds) . Release both buttons while the LED is blinking. both buttons while the LED is blinking. The LED will blink two times and then The LE

controlled devices such as a garage door opener, 2. Select the button you wish to use. with a single transmitter. 3. Enter your 9 digit code. Follow these simple instructions. Please read the instructions completely before starting. Further instructions are available at INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS Select the block of switches below that best matches the one in the transmitter or receiver that you are replacing. *The grids display an EXAMPLE using the code shown on the switches to t