To stop the tool in continuous operation, quickly press and release the trigger switch. Reversing Lever (Fig. 1) The reversing lever (H) is used to reverse the rotary hammer for backing out fasteners or jammed bits in drill-only mode. CAUTION: When reversing to clear jammed bits, be ready for strong reactive torque. To reverse the rotary hammer, turn it off and align the reversing lever (H) with the yellow arrow pointing backward (viewed when holding drill in operating position). To position the

It is located above the trigger, shown in Figure 2. D25101, D25103 To reverse the rotary hammer, turn it OFF and align the reversing lever (C) with the yellow arrow pointing backward (viewed when holding drill in operating position). To position the lever for forward operation, turn the rotary hammer OFF and align the reversing lever with the yellow arrow pointing forward (viewed when holding drill in operating position). D25201, D25203, D25303, D25304 To reverse the rotary hammer, turn it OFF a

Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results. We hope you enjoy using your drill. FEATURES OF THE PEBH 780 Chuck ON / OFF trigger Locking/unlocking cap Speed control wheel Depth stop Forward/reverse selector Function selector Trigger lock button Ventilation slots Auxiliary side handle TECHNICAL INFORMATION Nominal power: 780 W Sound pressure level: Lp = 99,6 dB(A) Nominal voltage:

6 CARTON CONTENTS 1 2 Fig. 1 1. Motor and blower assembly 2. Stand 3 4 5 6 7 8 9 Fig. 1A 3. Dust intake port 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Bag hanging rod (2) 7 1011 12 13 14 15 1617 1011 12 13 14 15 1617 Fig. 1B 10. Caster (4) 11. Intake cap and ring (3) 12. Bracket for bag hanging rod (2) 13. Knob for attaching legs to blower/motor assembly (4) 14. 3/8” (9.5mm) Lockwasher for a

To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. • Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemical

581054-00 D25101, D25103, D25201, D25203, D25303, D25304 Copyright © 2003 The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool. Questions? See us Wide Web at INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y POLIZA INSTRUCTION MANUAL DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE

J Protect the charger, battery pack and the drill/ grinder from moisture. J Warning! Do not use the drill/grinder with chargers or batteries other than the charger/ battery pack supplied. J Warning! Never short circuit the battery pack. Overheating, fire or destruction of the battery pack may result. Therefore: -Do not connect any wires to the battery pack poles. -Take care that no metal objects (nails, screws, etc.) can short circuit the battery pack connectors. J m Attention! Never throw the b

4. For masonry, use carbide-tipped bits or masonry bits. A smooth even flow of dust indicates the proper drilling rate. Chipping and Chiselling 1. To switch from hammer drilling to chiselling, first insert the SDS- plus® chisel and check if it is properly locked. 2. When switching from hammer drilling mode to chiselling mode, turn the chisel to the desired position. If you find resistance during mode change, turn the chisel slightly to engage the spindle lock. Depth Rod (Fig. 4) TO ADJUST THE DE

Damaged or entangled cords increase the risk of electric shock. e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock. 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating

2. Snap the steel ring (K) over the collar (L) behind the tool holder (M). Squeeze both ends of the steel ring together. Mount the bushing (N) and insert the pin (O). 3. Slide the side handle clamp (J) over the bushing and screw on the clamp knob (H)–do not tighten. 4. Screw the side handle (C) into the clamp knob (H) and tighten. 5. Rotate the side handle mounting assembly to the desired position. For hammerdrilling horizontally with a heavy drill bit, place the side handle assembly at an angle