Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Ampere Rating Volts Total Length of Cord in Feet Gauge of Extension Cord 0-6 120 up to 25 18 AWG 0-6 120 25-50 16 AWG 0-6 120 50-100 16 AWG 0-6 120 100-150 14 AWG 6-10 120 up to 25 18 AWG 6-10 120 25-50 16 AWG 6-10 120 50-100 14 AWG 6-10 120 100-150 12 AWG 10-12 120 up to 25 16 AWG 10-12 120 25-50 16 AWG 10-12 120 50-100 14 AWG 10-12 120 100-150 12 AWG 12-16 12-16 12-16 120 120 120 up to 25 25-50 14 AWG12 AWGGREATER THAN 50 FEET NOT RECOMMENDED Fig. D-1 6 FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION FOREWORD The Delta Model AP300 is a portable single stage dust collector. NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only. CARTON CONTENTS 6 2 3 7 9 8 1 12 14 4 18 18 15 16 17 5 13 2019 10 1. Dust collector 10. Casters (4) 2. Hose 11. Lower tube support clamps (2) 3. Dust bag 12. Adjustable locking lever 4. Exhaust flange 13. Hose clamps (2) 5. Exhaust flange gasket 14. 5/16-18x5/8" Button head carriage bolt (2) 6. Intake funnel 15. 5/16" Lockwasher 7. Intake support angle brace 16. 5/16-18 Flange hex nut (6) 8. Upper support bracket 17. 5/16-18x5/8" Hex head screw (4) 9. Lower tube support 18. Intake cap 19. M8.4 Flat washer 20. 3/8-16 Flange Hex nut (4) UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. 7 77 ASSEMBLY ASSEMBLY For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. ASSEMBLY TOOLS REQUIRED 1/2” & 9/16" Open or Box End Wrench - not provided 1/2” & 9/16" Socket and Drive - not provided Flat or Phillips Screwdriver - not provided ASSEMBLY TIME ESTIMATE Assembly for this machine takes approximately 1-2 hours. INSTALLING THE CASTERS 1. Place the dust collector on its side. 2. Insert a caster through the four holes (A) Fig. 3 in the base of the dust collector. 3. Thread a 3/8-16 flange hex nut (B) Fig. 4 onto each of the four bolts and tighten securely. INSTALLING THE EXHAUST FLANGE 1. Align the holes in the exhaust flange (A) Fig. 5 with the holes in the exhaust flange gasket (B). 2. Insert a 5/16-18x5/8" hex-head bolt through the exhaust flange, the exhaust flange gasket, and the base unit (Fig. 6). 3. Thread a 5/16-18 hex nut (B) onto the 5/16-18x5/8" hex head bolt (A) Fig. 6 and tighten securely. 4. Repeat this process for the three remaining bolts. Fig. 3 Fig. 4 Fig. 5 Fig. 6 A B A B A B 8 88 INSTALLING THE DUST PORT TUBE AND THE DUST COLLECTOR CONNECTOR Disconnect the machine from the power source! 1. Place the tube clamp (A) Fig. 7 on the lower support tube holder (B). 2. Insert the lower tube support (A) into the tube support holder (B) (Fig. 8). 3. Place a tube clamp (A) on the lower tube support (Fig. 9). Fig. 7 Fig. 8Fig. 9 A B A A B 4. Align the two holes in the intake support angle brace (A) Fig. 10 with the two holes in the intake funnel (B). 5. Fasten the intake support angle brace to the intake funnel by inserting the two 5/16-18x5/8" button-head carriage bolts (C) through the intake funnel (B) and the intake support angle brace (A) (Fig. 11). Fig. 10 Fig. 11 A B A B C 6. Thread a 5/16-18" flange hex nut (C) Fig. 12 on the bolt (B). Tighten securely. 7. Attach the upper support bracket (B) Fig. 13 to the intake support angle brace (C) with the adjustable locking lever (D). NOTE: Place an M8.4 flat washer and a 5/16” lockwasher on the locking lever screw before attaching it to the intake support angle brace. Fig. 12 B C Fig. 13 D C B 9 99 8. Place the intake funnel assembly (A) on the lower support tube (B) Fig. 14. Secure it with a tube clamp (C). Fig. 14 A C B ATTACHING THE VACUUM HOSE TO THE DUST COLLECTOR Disconnect the machine from the power source! 1. Place the intake cap holder (D) on the dust collector (Fig. 15). NOTE: Do not cover the intake port with the intake cap when attaching the hose to the intake port. 2. Place a hose clamp (A) Fig. 15 on the end of the vacuum hose (B). Slide the hose around the intake port (see the inset). Tighten the hose clamp (A). D C A B Fig. 15 3. P...