Remove those nuts and washers to free the wires. (Fig. 48) 4. Remove air deflector housing" and place on a clean work area. 5. Remove four screws securing the heating element brackets to the ceramic insulators with a medium (6") flathead screwdriver. (Fig. 49) 6. Slide brackets off the old element and discard the old element. 7. Slide brackets (large one first) over the connector end of the new heating element. (Fig. 50) 8. Reconnect heating element brackets to the ceramic insulators with the fo

78008. 1/0. Phone: +1 (214) 421-7366 Fax: +1 (214) 565-0976 Toll Free: +1 (800) 441-1601 BevLes Website: 729 Third Avenue E-mail: sales@BevLes.com Dallas, TX 75226 1 TABLE OF CONTENTS 1 2 3 4 5 6 7 2-1 2-2 2-3 2-4 2-5 3-1 3-2 4-1 4-2 4-3 4-4 5-1 5-2 6-1 6-1a 6-1b 6-1c 6-1d 6-1e 6-1f 6-1g 6-1h 6-1i 6-1j 6-1k 6-1l 6-1m 6-1n 6-1o 7-1 7-2 7-3 7-4 7-5 7-6 8-1a 8-1b WARRANTY 3 GETTING STARTED 4 INTRODUCTION 4 MODELS 4 UNPACKING 4 SETTING-UP 5 CLEANING. 5 OPERATION 6 OPERATING CONTROLS AND COMPONENTS 6

Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear scre

Tighten screws to secure power cord into connector. *"WARNING: Replace only with a BEVLES power cord properly rated for your unit. 8. Insert new wires through opening in back panel and reattach elbow connector. 9. Reattach green ground wire to back panel. 10. Reconnect power cord wires using wire nuts and wiring diagram. Retape over wire nuts and wires. (Diagram 3) **WARNING: Severe damage can be caused to your unit by improperly connecting wires. 11. Replace the back panel using the five philli

(Fig. 16) 3. Remove the nut, washer and retaining bracket and pull thermometer out the front of the panel. 4. Replace retaining bracket and insert new thermometer into opening. **NOTE: Align thermometer so that the 150° reading will be straight up when the front panel is replaced and the heating module is flipped over. (Fig. 17) 5. Replace and tighten washer and nut on rear of front panel. DO NOT OVER TIGHTEN! 6. Replace the front panel (section 6-1b). 6-1g. Replacing the power cord for a CA70 u

hd. s/. phillip. 9 Machine Screw, 1/4"-20 x .” phillips 11 Knob, thermostat 50-250°F 10 Latch 12 Socket Set Screw, Thermostat Knob #8-32 11 Latch Strike 13 Clamp, Thermostat Probe 12 Latch Pin, 5/16" x 8.5" rod 14 Power Switch, LTlGK-6S-WH-NBL 13 Latch Spring #CDL5019 15 Blower Motor 17 Air Duct Assembly (CV13) 16 Mounting Screw, #10-24 x 1/2" s/s phillips 19 Button, aluminum #l0-23-75R 17 Lockwasher, #10 S/S internal tooth 20 Sheet Metal Screw, T/H #8 x 1/4” phillips 18 Nut, #10-24 hex s/s 21 W

. 1/4. rd. hd. s/. phillips Mounting Screw, 11 82136 Knob, thermostat 50-250°F 12 70284 Socket Set Screw, Thermosta. Kno. #8-3. 13 83112 Clamp, Thermostat Probe 14 82082 Power Switch, LTIGK-6S-WH-NBL 15 82024 Blower Motor 16 70173 s/. phillips Mounting Screw, #10-24 x 1/2” 17 70144 Lockwasher, #10 s/s internal tooth 18 70141 Nut, #10-24 hex s/s 20 41068 Motor Air Duct Cover 21 41052 Water Pan Slide 22 82124 1500W. 120. Heating Element, 22A 82296 Heating Element, 1800W. 120. (M. o. H. Mdls. 23 41

phillip. 15 82024 Blower Motor 16 70173 Mounting, Screw #10-24 x .” s/. phillip. 17 70144 Lockwasher, #10 s/s internal tooth 18 70141 Nut, #10-24 hex s/s 19 41068 Motor Cover 20 41072 Air Duct Cover 37 41072 Motor Housing Cover 37A 41136 Motor Housing Cover, MP 38 41172 Air Flow Cover Extension, MP 7-6l. Heating Element Parts List (CA43 Mdls) Dwg 7-5c Ref # DescriptionPart Number 22 82124 Heating Element, 1500W. 120. 22A 82296 Heating Element, 1800W. 120. (M. o. H. Mdls. 23 41044 Front Clip, 0.8

2. Gently lift off the front panel while guiding attached wires and thermometer probe to prevent damage. (Fig. 9) 3. Leaving wires attached, gently place front panel face down on a clean work space. (Fig. 10) 4. To replace front cover, reinsert thermometer probe into receptacle, guide wires back into place and reattach panel with the five phillips head screws. Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 6-1c. Replacing the power indicator lamp module. Required: Wiring markers (colo

3. Call the BEVLES manufacturing facilities at (214) 421-7366 or (800) 441-1601 (outside of Texas andAlaska). 7-2 PRICES Your distributor can provide you with a current price list for replacement parts. Or, call the BEVLES manufacturing facilities for the most recent prices. 7-3 SHIPPING Common parts are in-stock for immediate processing. Normally, replacement parts will be shipped within two working days. 7-4 WARRANTY Replacement parts are fully covered by the parts provisions of the BEVLES qua