Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Tighten screws to secure power cord into connector. *"WARNING: Replace only with a BEVLES power cord properly rated for your unit. 8. Insert new wires through opening in back panel and reattach elbow connector. 9. Reattach green ground wire to back panel. 10. Reconnect power cord wires using wire nuts and wiring diagram. Retape over wire nuts and wires. (Diagram 3) **WARNING: Severe damage can be caused to your unit by improperly connecting wires. 11. Replace the back panel using the five phillips head screws. 1. Figure 24 Figure 25 Figure 24 Figure 25 Figure 26 Powe. Cor. (Grd. (2. (3. (4. Heatin. Elemen. (1. (4. (5. Klixo. Thermosta. (0. (1. (0. (1. Powe. Indicato. Lam. (5. (1. Thermosta. Indicato. Lam. Coolin. Fa. Powe. Switc. (0. (1. (2. (3. (0. (5. Thermosta. (0. (1. Fa. Blowe. Diagram 3 Figure 27 Figure 28 Figure 29 6-1i. Replacing the thermostat for a CA70. Required: Small flathead screwdriver, Medium (6") flathead screwdriver, Medium (6") phillips screwdriver, Wiring markers (color or number codes), Electrical tape, Wiring diagram for thermostat (see step 9) 1. Remove top mounted heating module and front panel as found in sections 6-1a and 6-1b. 2. Mark all the wires connected to the thermostat with a color code or number to make proper re-connection easy. (Fig. 27) 3. Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the set screw with a small flathead screwdriver. (Fig. 28) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. Figure 30 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6” flathead screwdriver. (Fig. 29) 6. Remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. (Fig. 30) 1. Figure 31 Figure 32 7. Pull the copper thermostat probe and tubing from the fan blower motor assembly area through the opening to the front cover (it may be necessary to feed the probe, into the bottom of the assembly area under the fan blower to achieve the correct angle). (Fig. 31) DO NOT bend or kink the copper tubing when replacing the thermostat probe. 8. Disconnect wires from rear of thermostat by reversing screw terminals with a flathead screwdriver. 9. Connect wires to the rear of a new thermostat unit using the thermostat wiring diagram for CA70 units. Re-tape over wire nuts and wires. (Diagram 4) 10. Attach new thermostat to rear of front panel and bezel to the front of panel with the two phillips screws. The tops of the terminals should face down (toward the actual top of the heating module). (Fig. 32) 11. Carefully guide new copper probe and tubing through the opening to fan blower motor housing and reattach probe clips with two flathead screws. (Fig. 31) DO NOT kink or bend the copper probe or tubing. 12. Replace fan blower motor assembly cover with two front and two rear flathead screws. Do not over tighten. 13. Replace thermostat dial, tightening set screw securely. 14. Replace top mounted heating module and front panel (sections 6-1a and 6-1 b). **NOTE: **NOTE: **NOTE: FanBlower(0)(1)(0)(1)PowerIndicatorLamp(5)(1)ThermostatIndicatorLampPowerSwitch(0)(1)(2)(3)(0)(5)Thermostat Diagram 4 PowerCord(Grd)(2)(3)(4)(1)HeatingElement(4)(5)KlixonThermostat(0)(1)CoolingFan 6-1j Replacing the thermostat for CA43 units. Required: Small flathead screwdriver, Medium (6”) flathead screwdriver, Medium (6”) phillips screwdriver, Wiring markers (color or number codes), Electrical tape, Wiring diagram for thermostat (see step 11) 1. Remove top mounted heating module and front panel as found in sections 6-1a and 6-1b. 2. Mark all the wires connected to the power cord with a color Figure 33 Figure 34 Figure 31 Figure 32 7. Pull the copper thermostat probe and tubing from the fan blower motor assembly area through the opening to the front cover (it may be ...
Эта инструкция также подходит к моделям:Мебель - CA43-CV7 or CV13 (1.57 mb)
Мебель - CA43-CV9 (1.57 mb)
Мебель - CA70-CV16 or CV32 (1.57 mb)
Мебель - Convection Heated Holding Cabinet CA34-CV9 (1.57 mb)