Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
(Fig. 16) 3. Remove the nut, washer and retaining bracket and pull thermometer out the front of the panel. 4. Replace retaining bracket and insert new thermometer into opening. **NOTE: Align thermometer so that the 150° reading will be straight up when the front panel is replaced and the heating module is flipped over. (Fig. 17) 5. Replace and tighten washer and nut on rear of front panel. DO NOT OVER TIGHTEN! 6. Replace the front panel (section 6-1b). 6-1g. Replacing the power cord for a CA70 unit. Required: Medium (6”) phillips screwdriver, Medium (6") flathead screwdriver, Wiring markers (color or number codes), Electrical tape, Wiring diagram for CA70 (see step 10) 1. Remove top mounted heating module and front panel as found in sections 6-1a and 6-1b. 2. Mark all the wires connected to the power cord with a color code or number to make proper re-connection easy. (Fig. 18) . 3. Turn the top mounted heating unit over so that the elbow connector for the power cord is up. Free the green ground wire by grasping the nut with fingers or pliers (under front overhang of the heating module) and remove the screw from the exposed surface of the module with a medium (6") phillips screwdriver. (Fig. 19). 4. Free the other two power cord wires by removing the two wire nuts that connect them. 5. Remove elbow connector that secures power cord into the heating module by grasping the nut holding the connector (under the overhang of the heating module). Rotate the nut to loosen and remove the elbow from the module. (Fig. 20) 6. Remove the two screws that secure the power cord into the compression end of the elbow connector with a medium (6”) flathead screwdriver. Pull gently to free power cord from the elbow connector. (Fig. 21) 7. Insert new power cord into elbow connector and replace compression screws. Tighten screws to secure power cord into connector. **WARNING : Replace only with a BEVLES power cord properly rated for your unit. 8. Insert new wires through opening in the heating module and reattach elbow connector. 9. Reattach green ground wire to module. 10. Reconnect power cord wires using wire nuts and wiring diagram. Re-tape over wire nuts and wires. (Diagram 2) **WARNING: Severe damage can be caused to your unit by improperly connecting wiring. 11. Replace the front panel and top mounted heating module (sections 6-1a. and 6-1 b). 1. Figure 20 Figure 20 6-1h. Replacing the power cord for a CA43. Required: Medium (6”) phillips screwdriver, Medium (6") flathead screwdriver, Wiring markers (color or number codes), Electrical tape , Wiring diagram for CA43(see step 10) 1. Remove the back panel of the module by removing the five phillips head screws and gently lifting out the back panel. Lay the panel on a clean work surface. (Fig. 22) (0. (4. (5. HeatingElement (1. Cooling Klixo. Fan (Grd. Thermosta. (2. (3. Powe. Cor. (0) (5) (0. (1. (4. (1. FanBlower Thermosta. (1) (0. (1. (5. (1) (0. (2. (3. Thermosta. Indicato. Lam. Powe. Switc. Indicato. Lam. Powe. Diagram 2 Figure 21 Figure 22 Figure 23 2. Mark all the wires connected to the power cord with a color code or number to make proper re-connection easy. (Fig. 23) 3. Free the green ground wire by grasping the nut with fingers or pliers (inside the back panel of module) and remove screw from the outside surface of the panel with a medium (6") phillips screwdriver. (Fig. 24) 4. Free the other two power cord wires by removing the two wire nuts they are attached to. 5. Remove elbow connector that secures power cord onto the back panel. While grasping the nut (on the inside surface of the panel) and holding the connector (on the outside surface of the panel), rotate the nut to loosen and remove the elbow from the panel. (Fig. 25) . 6. Remove the two screws that secure the power cord into the compression end of the elbow connector with a medium (6”) flathead screwdriver. Pull gently to free power cord from the elbow connector. (Fig. 26) 7. Insert new power cord into elbow connector and replace compression screws. Tighten screws to secure power cord into connector. *"WARNING: Replace only...
Эта инструкция также подходит к моделям:Мебель - CA43-CV7 or CV13 (1.57 mb)
Мебель - CA43-CV9 (1.57 mb)
Мебель - CA70-CV16 or CV32 (1.57 mb)
Мебель - Convection Heated Holding Cabinet CA34-CV9 (1.57 mb)