Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6”) flathead screwdriver. (Fig. 35) 6. Pry off fan blower housing cover (with a flathead screwdriver, if necessary). Without disconnecting wires, set cover on a clean work area. (Fig. 36) 7. Remove four screws (two at each end) holding fan blower motor bracket in place with a medium flathead screwdriver and gently lift bracket to expose mounting clips for the copper thermostat probe. (Fig. 37) 1. Figure 35 Figure 35 Figure 36 8. Remove the two screws and nuts securing the clips that attach the copper thermostat probe to the motor bracket. Use a medium flathead screwdriver. (Fig. 38) 9. Pull copper probe and tubing from fan blower motor area through the opening to the front panel. **NOTE: DO NOT bend or kink the copper tubing when replacing the thermostat probe. 10. Disconnect wires from rear of thermostat by reversing screw terminals with a flathead screwdriver. 11. Connect wires to the rear of a new thermostat unit using the thermostat wiring diagram for CA43 units. Re-tape over wire nuts and wires. (Diagram 5) 12. Attach new thermostat to rear of front panel and bezel to the front of panel with the two phillips screws. **NOTE: The tops of the terminals should face down (toward actual top of the heating module). (Fig. 39) 13. Carefully guide new copper probe and tubing through opening to fan blower motor area and reattach probe clips to motor bracket with two flathead screws. **NOTE: DO NOT kink or bend the copper probe or tubing. 14. Replace fan blower motor bracket with two phillips screws front and two rear. 15. Replace fan blower motor housing cover, carefully guiding the wires to prevent damage. 16. Replace fan blower motor assembly cover with two front and two rear flathead screws. 17. Replace thermostat dial, tightening set screw securely. 18. Replace top mounted heating module and front panel (sections 6-1 a. and 6-1 b). Figure 39 Figure 38 Figure 37 Powe. Cor. (Grd. (2. (3. (4. Heatin. Elemen. (1. (4. (5. Klixo. Thermosta. (0. (1. (0. (1. Powe. Indicato. Lam. (5. (1. Thermosta. Indicato. Lam. Coolin. Fa. Powe. Switc. (0. (1. (2. (3. (0. (5. Thermosta. (0. (1. Fa. Blowe. Diagram 5 1. 6-1k. Replacing the fan blower motor assembly. Figure 40 Figure 41 Figure 42 Required: Medium (6") flathead screwdriver, Medium (6”) phillips screwdriver, Crescent or standard wrench, Wiring markers (color or number codes), Electrical tape 1. Remove top mounted heating module as found in section 6-1a. 2. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear screws with a medium (6”) flathead screwdriver. (Fig. 40) 3. Pry off fan blower housing cover (with a flathead screwdriver, if necessary). Without disconnecting wires, set cover on a clean work area. (Fig. 41) 4. Mark all the wires connected to the fan blower motor(s) with a color code or number to make proper re-connection easy. (Fig. 42) 5. Remove wire nuts and set cover aside. 6. For CA70 units, remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. Free the copper probe and carefully set out of the way. (Fig. 43) **NOTE: DO NOT kink or bend copper tubing or probe. Remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver. 7. For CA43 units, remove four screws (two at each end) that hold the fan blower motor bracket in place. Use a medium flathead screwdriver. Gently lift bracket to expose mounting clips for the copper thermostat probe. Remo...
Эта инструкция также подходит к моделям:Мебель - CA43-CV7 or CV13 (1.57 mb)
Мебель - CA43-CV9 (1.57 mb)
Мебель - CA70-CV16 or CV32 (1.57 mb)
Мебель - Convection Heated Holding Cabinet CA34-CV9 (1.57 mb)