When saw is properly positioned, drive a small nail through hole in cross bar. Using rip fence as a pivot arm, begin cutting circle. For circle cutting, the cross bar should be up, as shown in Figure 5. When ripping, slide the rip fence under the screw from either side of the saw. Set the cross bar at desired distance from blade and tighten screw. For ripping, the cross bar should be down and against the straight edge of the workpiece. MAINTENANCE Use only mild soap and damp cloth to clean the t

Place three rubber mounting feet from hardware bag into the three mounting holes. Always mount your saw firmly to prevent movement. Do not over tighten mounting bolts. Leave some cushion in the rubber feet for absorbing noise and vibration. Aligning the Blade With the table Top This is most easily accomplished with a carpenter’s tri-square. Begin by installing a blade in the saw. Next, place the tri-square on the table top, close to the blade. Observe the alignment of the blade to the edge of th

Variable speed switch 2. Lock-on button 3. Saw blade locking lever 4. Saw blade support roller 5. Dust blower 6. Shoe plate 7. Dust extraction port 8. Saw blade storage compartment USE OF EXTENSION CORDS Make sure the extension cord is in good condition before using. Always use the proper size extension cords with the tool – that is, proper wire size for various lengths of cord and heavy enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in line voltage r

Minimum Gauge for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 (0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m) 240V 0-50 51-100 101-200 201-300 (0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m) Ampere Rating More Not more American Wire Gauge Than Than 0 -6 18 16 16 14 6 -10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK: • Do not connect to AC distribution wiring. • Do not make any electrical connections or dis

CAUTION — RECHARGEABLE DEVICES • Certain rechargeable devices are designed to be charged by plugging them directly into an AC receptacle. Thesedevices may damage the inverter or the charging circuit. • If there is any sign that your appliance is behaving differently to that when connected to the normal power sourcethen unplug and seek advice from your appliance manufacturer. • This problem does not occur with most of the battery-operated equipment. Most of these devices use a separatecharger or

This will prevent the saw from jumping or vibrating and minimize blade breakage. VARIABLE SPEED SWITCH (FIGURE 2) The variable speed trigger switch will give you added versatility. The further the trigger is depressed the higher the speed of the saw. To turn the tool “OFF” release the trigger. NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked in the ON position by any other means. BLADE CLAMP RELEASE LEVER (FIGURE 3) CAUTION: TURN OFF AND UNPLUG F

warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, check country specific warranty information contained in the packaging, call the local company or see the website for warranty information. See .Tools- Black & Decker Electric. (U.S.) Inc., – Yellow Pages – Towson, MD 21286 for Service & 701 E. Joppa Rd. U.S.A. Sales MODE D’EMPLOI Merci d’avoir choisi Black & Decker! Consulter le site Web pour enregistrer votre nouveau produit. A LI

The batteries can explode in a fire. 13. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention

Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-6986 or visit Full Two-Year Home Use Warranty Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, w