Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The batteries can explode in a fire. 13. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. Charging the Battery Pack THE BATTERY PACK IS NOT FULLY CHARGED AT THE FACTORY. BEFORE ATTEMPTING TO CHARGE THE BATTERY PACK, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS. The charger is designed to use standard household 120 volt 60 Hz power. 1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge by means of an engine generator or DC power source. Use only 120V AC 2. Slide the charger onto the battery pack as shown in Figure 1 and let the battery charge initially for 9 hours. After the initial charge, under normal usage, your battery pack should be fully charged in 3 to 6 hours. 3. Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. NOTE: To remove the battery from the saw, press down on the release button on the back of the battery (Figure 2) and slide out. Important Charging Notes 1. After normal usage, your battery pack should be fully charged in 3 to 6 hours. If the battery pack is run-down completely, it may take up to 6 hours to become fully charged. Your battery pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours. 2. DO NOT charge the battery pack in an air temperature below 40°F (4,5 °C) or above 105°F.(40,5 °C) This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F.(24°C). 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the battery pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and battery pack to a surrounding air temperature of 40°F (4,5 °C) to 105°F.(40,5 °C) (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the battery pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its battery pack in a depleted condition. 6. To prolong battery pack life, avoid leaving the battery pack on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantly reduce overall battery pack life. 7. The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. Maintenance Stage The trickle charge feature of the charger allows the battery pack to remain in the charger and ready for use. With the charger connected to standard household current, the red charging indicator light will glow constantly. The charger will keep the battery pack fully charged. A battery pack will slowly lose its charge when kept out of the charger. Removing & Refitting the Blade WARNING: Always ensure that the battery is removed from the tool when changing blades. Removing the Blade (Figure 3) Ensure blade has cooled after use. Press and hold the rear of the black blade release button fully, hold the back of the blade and rotate it 90 degrees in a downward direction. Slide the blade sideways off the location pin and remove from the saw. Fitting a Blade (Figure 4,5) Place the blade, with the tooth protector fitted, over the location pin. The blade teeth should be facing the handle. Rotate the blade through 90° until it is fully located in the slot and the location pin is in the locked position.To ensure the blade is securely fitted try to remove without pressing the blade release button. Remove the tooth protector, your saw is now ready for use. NOTE: If you are unable to fit the blade, check to see if the slot in the location pin is straight up and down. If it is not, keep the blade release button depressed and use a flat bladed screwdriver to turn the location pin into the correct position as shown in Figure 5. Operating Instructions WARNING: When cutting, hold saw firmly w...
Эта инструкция также подходит к моделям:Лобзики и пилы - 5105119-02 (299.31 kb)
Лобзики и пилы - BDPHS1400 (299.31 kb)