Войти:
Скачали: 0   Размер: 8 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

Be sure to keep your fingers well away from the Trigger (4), Safety (21), and Blade (10) while performing any adjustment, but especially when adjusting the Depth, because the battery may be installed. B. Loosen the Depth Knob (34). C. Raise/lower the Saw body in relation to the Foot (35) to adjust the depth. Note: Add 1/8” to the depth so the Saw Blade (10) can cut through the material cleanly. D. Retighten the Depth Knob (34) securely. 5. Make certain that both halves of the workpiece are prope

Скачали: 4   Размер: 6 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

Never attempt to discharge a tool’s battery by continuing to pull the tool trigger. When tool performance begins to diminish, stop the tool, recharge the battery and use the fresh battery for optimal performance. 1. When a Battery (47) requires recharging, a 3 to 5 hour* charge allows the tool to operate at full power. Do not recharge the Battery longer than 5 hours*, as damage to the Battery and/or tool will occur. 2. To charge the Battery (47), plug the AC Charger Adapter’s (53) plug into the

Скачали: 0   Размер: 5 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

11. Adjust the Saw Blade to 45 degrees. Raise and lower the Saw Blade through the full range. Readjust the Saw Blade to 90 degrees, then raise and lower the Saw Blade through the full range. There should be no contact between the Saw Blade, the Main Table, the Table Insert, or any other part of the Table Saw. If there is contact, have a qualified service technician make the necessary adjustments before using the Table Saw. To AdjustThe 45 Degree And 90 Degree Positive Stops: 1. The Stops have be

Скачали: 0   Размер: 5 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

(See Figure L.) 3. If the transparent Safety Cover (72) becomes so dirty that the Saw Blade (4) cannot be seen clearly, disconnect the electrical Power Cord from its electrical outlet and clean the Safety Cover with a soft, damp, cloth. A mild detergent may be used, but do not use solvents which may damage the Safety Cover. (See Figure L.) (72) SAFETY COVER BLADE CASE (54) CAUTION! Never disconnect or remove Safety Cover (72). FIGURE L The Safety Button And Switch Lever: 1. Before plugging in th

Скачали: 1   Размер: 4 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

Page 17 To UseThe QuickVise Adjustment For An Angle Cut: To UseThe QuickVise Adjustment For An Angle Cut: . Loosen the Hex Bolt (136), and move the Mitering Vise Plate (138) to the threaded hole position. Adjust the Mitering Vise Plate to the desired angle as indicated by the Angle Scale (165). Loosen the Hex Bolt (139), and adjust the Moveable Vise Plate (141) to parallel the Mitering Vise Plate. Then, re-tighten the Hex Bolt. (See Figure Q.) THREADED HOLE POSITION MITERING VISE PLATE (138) HEX

Скачали: 11   Размер: 3 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

(See Figure H.) Turn on the Bandsaw. The Saw 2. Blade (82) is tracking properly when the back of the Blade is just touching the edge of the Blade Wheel (37) flange. The back of the Blade should not be rubbing against the flange. (See Figure P.) If adjustment is necessary, the Blade 3. Guide Bearings (88, 92, 100, 104) should be clear of the Saw Blade (82). (See Figure N.) HEX BOLT (21) LOWER SCREW (22) BLADE TENSIONADJUSTING KNOB(34) BLADE WHEEL(37) FIGURE O 4. Loosen the middle Hex Bolt (21) to

Скачали: 2   Размер: 3 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

Position the Vertical Cutting Plate Support against the Body Frame (60). Then firmly re-tighten the Hex Head Bolt. (See Figures I and J.) OPERATING INSTRUCTIONS CAUTION! Turn the Power Switch (164) to its “OFF” position and unplug the tool from its electrical outlet prior to making adjustments to the tool. To Use The Vise: Raise the Body Frame (60) to its 1. vertical position, and lock the Body Frame in place with the Support Plate (150) and Locking Pin (153). (See Figure H.) FIGURE KMOVEABLE VI

Скачали: 4   Размер: 2 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. REQUIRED MINIMUM EXTENSION CORD GAUGE - 110 VOLT NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 0-25 FT. 25-50 FT. 50-100 FT. 100-150 FT. 618 16 14 12 8 16 16 12 10 10 16 14 12 1012 16 14 10 814 14 12 10 816 14 1

Скачали: 3   Размер: 2 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

PAGE 7 FIGURE H (REAR VIEW) FIGURE H (REAR VIEW) 1. With additional help, set the Bandsaw Body on the Stand. Make sure the Table (36B) faces to the frontof the Stand. 2. Align the four mounting holes on the Base (2B) of the Bandsaw Body with the holes located on the Face Plate (1A) of the Stand. 3. Attach the Bandsaw Body securely to the Stand, using the four Hex Bolts, Washers, Spring Washers, and Nuts (III). (See Figures I, J, and Hardware Diagram.) FIGURE I FIGURE J REAR VIEW To MountThe V-Be

Скачали: 0   Размер: 2 mb   Производитель: Harbor Freight Tools  
Категория: Лобзики и пилы
@name

Rotate the Relief Stops (39A) out and screw in the Tapping Screws (40A) to secure the Side Panel in place. Repeat the process for the other Side Panel (38A). To InstallThe Saw Blade: Wear Gloves; be careful of sharp blade teeth when handling. 1. Remove the four Knobs (15B) from the Upper and Lower Wheel Guards (14B, 21B). (See Figure P.) 2. Remove and set aside the Upper and Lower Wheel Guards (14B, 21B). 3. Remove the Table Insert (37B) and Table Pin (38B). (See Figure Q.) FIGURE N FIGURE P FIG





Категории