Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together. • These chargers are not intended for any uses other than charging designated PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. •

Shorting the battery terminals together may cause burns or a fire. d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. SPECIFIC SAFETY RULES • Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. • When working on a ladder or on scaffolding be sure t

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 6. Do not freeze or immerse charger in water or any other liquid. : Shock hazard. Do not allow any liquid to get inside charger. : Never attempt to open the battery pack for any reason

When using air tools, basic safety precautions should always be followed to reduce the risk of personal injury. IMPORTANT SAFETY INSTRUCTIONS IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE. READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT.WHEN USING AIR TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF PERSONAL INJURY. SAVE! IMPORTANT SAFETY INSTRUCTIONS SAVE! HAZARD RISK OF

B. That the extension cord is properly wired and in good electrical condition. C. Wire Size of cord is at least as specified in following chart: LENGTH OF CORD IN FEET 25 50 100 150 AWG SIZE OF CORD 18 18 18 16 D. If an extension cord is to be used outdoors it must be marked with the suffix W-A or W following the cord type designation. For example – SJTW-A to indicate it is acceptable for outdoor use. 8. Do not operate charger with damaged cord or plug – have them replaced immediately, to avoid

NOTES: If the blade clamp collar resists rotation to remove a blade, A Fig. 3 7 work the blade up and down while rotating the clamp (in a counterclockwise direction). If the blade breaks leaving nothing to grasp (to pull it from the clamp), it may be necessary to use another blade as a tool to aid in removing the broken piece (see Fig. 4). While holding the release collar in the open position, use the tip of another blade to “hook” the broken piece and pull it from the clamp. (A thin, fine-tooth

Postfach 30 D-73461 Westhausen Safety Recommendations For your safety and the safety of others, read and understand the safety recommendations before operating this saw. Always wear protective equipment. WARNING! Impact resistant eye protection must be worn while operating or working near this tool. Caution: Faceshields do not provide unlimited protection against flying particles and are not to be considered as eye protection. ANSI Z87.1 states that separate eyewear shall be used. For additional

Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 3. Keep blades sharp. Sharp blades will do the job better and safer. 4. Keep hands away from cutting area. When sawing never reach underneath or behind the material being cut for any reason. 5. When you have finish