Войти:
Сортировка : Названию ↑   Загрузкам   Оценке   Размеру ↑  
Скачали: 3   Размер: 613 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

Advertencia: Cuando el disco inicie el corte, suelteinmediatamente la palanca del mecanismo retractil Motor Your Black & Decker tool is powered by a Black & Decker-built motor. Be sure your power supply agrees withnameplate marking. 120 Volts AC only means your saw will operate on standard 60 Hz household power. Donot operate AC tools on DC. A rating of 120 volts AC/DC means that your tool will operate on standard 60Hz AC or DC power. This information is printed on the nameplate. Lower voltage w

Скачали: 0   Размер: 476 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

On/off switch 2. Lock-off button 3. Shoe 4. Blade clamp release lever 5. Blade 6. Battery compartment 7. Battery release button (on battery) 1 23 4 5 6 A 7 C D E B 5 90520983 VPX1301 Cut SAW 7/19/07 3:03 PM Page 6 I G H F IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGERS SAVE THESE INSTRUCTIONS: This manual contains important safety instructions for battery chargers. • Before using charger, read all instructions and cautionary markings on charger, battery pack, and product using battery pack. W

Скачали: 1   Размер: 691 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

This does not indicate a failure. However, if the outer seal isbroken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide. SAVE THESE INSTRUCTIONS INTRODUCTION READ A N D U N D E R S TA N D A L L OF THE INSTRUC

Скачали: 1   Размер: 476 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

NOTE: Battery pack performance will decrease under heavy use conditions when temperature is below 32°F (0°C). As the battery cells heat up the performance will improve. INSTALLING AND REMOVING THE BATTERY PACK (FIGURE D,E) CAUTION: Make certain the lock-off button is engaged to prevent switch actuation before removing or installing battery. Installing the battery pack: Insert the metal terminal end of the battery pack into the product until you hear the lock snap into place and the VPXTM logo sh

Скачали: 2   Размер: 4 mb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

L1. The blade teeth will dig into the scrap wood and prevent rotation of the blade. • Tighten the blade clamping screw securely with the blade wrench. NOTE: The blade wrench is stored in the saw housing as shown in figure M. Lower Blade Guard WARNING: Laceration Hazard. The lower blade guard is a safety feature which reduces the risk of serious personal injury. Never use the saw if the lower guard ismissing, damaged, misassembled or not working properly. Do not rely on the lower blade guard to p

Скачали: 0   Размер: 4 mb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name

Failure to do so can cause stalling and kickback. Any other conditions which could result in pinching, binding, twisting, or misalignment of the blade could cause kickback. Refer to the sections on “Adjustments and Set-Up” and “Operation” for procedures and techniques that will minimize the occurrence of kickback. TOOL LUBRICATION NOTE: With a new saw, change the oil after the first 10 hours of use and once per year after that. This action will greatly extend the life of your unit. 1. Always

Скачали: 1   Размер: 1 mb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

The cut-off stock remains on the table and is not touched until the saw blade has stopped, unless it is a large piece allowing safe removal. When ripping boards longer than three feet, use a work support at the rear of the saw to keep the workpiece from falling off the saw table. 2. If the ripped work is less than 4 inches wide, a push stick should always be used to complete the feed, as shown in Fig. 41. The push stick can easily be made from scrap material as explained in the section Fig. 41 “

Скачали: 0   Размер: 9 mb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

To release from lock position, squeeze and release the trigger switch once. Always disengage the the lock before disconnecting from the power supply. BEVEL ADJUSTMENT (FIGURES 3 &4J TURN OFF AND UNPLUG TOOL The shoe (5) can be angled up to 45° on either side. To do this, disconnect your jig saw from the power supply. Raise the dust shroud (3) and loosen both screws on the shoe plate with a screwdriver. Pull the shoe plate backward a little, and set the desired angular adjustment according to t

Скачали: 0   Размер: 503 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

Profundidad correcta: un diente debajo de la superficie de madera Battery Cap A B 8 Blade Lame Disco Inner clamp washer Rondelle de fixation externe Roldana de sujecion exterior Saw spindle Arbre de la scie Flecha de la sierra Blade clamping screw Vis de fixation de la lame Tornillo de sujecion del disco Outer clamp washer Rondelle de fixation externe Roldana de sujecion interior Direction of teeth Sens des dents Direccion de los dientes Kerf Plate and Screw Plaque de trait de scie et vis Placa

Скачали: 0   Размер: 391 kb   Производитель: Black & Decker  
Категория: Лобзики и пилы
@name@name@name

Please see the individual charger manuals for all safety and operating instructions. 18V Slide Pack Batteries 18V Firestorm Battery 18V FSXtreme Battery 18V FSXtreme Battery - 3 terminal 18V FSXtreme Battery - Silver Series 18V Black & Decker Battery FSB18 FS180BX FS18BX FS18SBX HPB18 Cat. # Description 18V Slide Pack Chargers 18V Cup Charger 18V Dual Port Charger 18V Radio Charger 18V Three Port Charger 9.6V-18V Fast Charger 9.6V-24V One Hour Charger 9.6V-24V Dual Port One Hour Charger FS18C FS





Категории