Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. WEAR PROPER APPAREL. Do not 10. wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. ALWAYS USE SAFETY GLASSES. 11. Also use face or dust mask if cutting operation is dust

If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Assembly WARNING! Always make sure that the unit is off and unplugged before assembly. The Guide Bar needs (63) to be assembled to the bandsaw for proper operation. Remove the Screws (62) on the Frame (21), along with their Spring and Flat Washers (47, 46). Install the Guide Bar around the blade as shown using the Screws (62), Spring Washers (47), and Flat Washers (

Support large panels to minimize risk of blade pinching and saw kickback. 2. Use the supplied Rip Guide (402) when ripping material by sliding it into the Base Assy. and tightening Wing Bold (58). See Figures F and G below. 3. Securely clamp material to be cut to work bench. 4. Make sure saw does not cut into supports or workbench. 5. Use the appropriate type of blade for the material you are cutting. Side Handle (401) Brush Cap (30) Wing Nut (60) Wing Bolt (58) Base Assy. (52) Lock Handle (55)

® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. © Copyright 2006 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions, please call 1-800-444-3353. PRODUCT SPECIFICATIONS SAVE THIS MANUAL Item Description Electric

7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. REQUIRED MINIMUM EXTENSION CORD GAUGE - 110 VOLT NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 0-25 FT. 25-50 FT. 50-100 FT. 100-150 FT. 618 16 14 12 8 16 16 12 10 10 16 14 12 1012 16 14 10 814 14 12 10 816 14 1

Chargers should not be left plugged in or charging for more than 2 hours. Operation Install saw blade. Prepare and secure the material to be cut before turning on saw. Battery should have a full charge before using saw. Refer to illustrations that follow. Remove battery before making any adjustments. Warning: Do not hold tool by the handle while making adjustments as your fingers may touch the Switch and Safe buttons and start the saw. Installing Cutting Blade 1. Remove battery. 2. Press on the

PAGE 7 FIGURE H (REAR VIEW) FIGURE H (REAR VIEW) 1. With additional help, set the Bandsaw Body on the Stand. Make sure the Table (36B) faces to the frontof the Stand. 2. Align the four mounting holes on the Base (2B) of the Bandsaw Body with the holes located on the Face Plate (1A) of the Stand. 3. Attach the Bandsaw Body securely to the Stand, using the four Hex Bolts, Washers, Spring Washers, and Nuts (III). (See Figures I, J, and Hardware Diagram.) FIGURE I FIGURE J REAR VIEW To MountThe V-Be

Page 17 To UseThe QuickVise Adjustment For An Angle Cut: To UseThe QuickVise Adjustment For An Angle Cut: . Loosen the Hex Bolt (136), and move the Mitering Vise Plate (138) to the threaded hole position. Adjust the Mitering Vise Plate to the desired angle as indicated by the Angle Scale (165). Loosen the Hex Bolt (139), and adjust the Moveable Vise Plate (141) to parallel the Mitering Vise Plate. Then, re-tighten the Hex Bolt. (See Figure Q.) THREADED HOLE POSITION MITERING VISE PLATE (138) HEX

It may be used on wood or metal stock. Read this manual before attempting to use the Jigsaw. OPERATION General Avoid overloading the tool. Do not apply excessive pressure to the saw while cutting. If the speed drops abnormally, decrease pressure immediately. If the blade stops abruptly or becomes blocked, turn saw off at once. Never use damaged blades. Ensure the safety of the work space. Clear the work area of all parts and debris that may cause injury by becoming flying objects. Use a stab

3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between different processes. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. SAFETY SETUP OPERATION MAINTENAN