Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
3. Wear suitable gloves to reduce the vibration effects on the user. 4. Use tools with the lowest vibration when there is a choice between different processes. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. SAFETY SETUP OPERATION MAINTENANCE Specifications Electrical Input 120V~ / 60Hz / 15A Motor No Load Speed 3,500 RPM Max. Accessory Diameter 14. Recommended Cut.Off Wheel Types 14. Cut.Off Wheel for Metal (SKU 44814, included) 14. Cut.Off Wheel for Masonry (SKU 44815) Cutting Capacity 4-1/4. Quick Release Vise Capacities 7. (1st Setting), 9-1/2. (2nd Setting) Arbor Size 1. 250100 Setup - Before Use Functions Base (13) Handle (100,109) MotorHousing(75) Vise Handle (28) Trigger (103) Lock Lock Ball (25) Depth AdjustmentBolt (16) Nut (15) SAFETY SETUP OPERATION MAINTENANCE Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Release the Trigger, unplug the tool from its electrical outlet and allow the wheel to cool completely before performing any inspection, maintenance, or cleaning procedures. To Remove or Install a Cut.Off Wheel 1. Raise the Saw if it is locked down by pushing down on it and pulling out the Lock Ball (25). 2. Open the Swing Guard (53) and tighten the Bolt (112) to secure it while working on the Wheel. 3. Push the Lock Pin (63) towards the Fixed Guard (60) as shown in Figure A. Rotate the wheel until the Lock Pin (63) slides into place. Figure A: Lock PinLock Pin (63) Fixed Guard (60) Handle 4. While continuing to hold down the Lock Pin (63), use the Hex Key (111a) to loosen the Socket Head Bolt (54). See Figure B. Figure B: Socket Head BoltLock Pin (63) Hex Key (111a) Socket Head Bolt (54) 5. Remove the Socket Head Bolt (54), the Flange Washer (96), the Outer Flange (55), and the Cut.Off Wheel (56). See Figure C. Socket Head Bolt (54) Flange Washer (96) Outer Flange (55) Cut.Off Wheel (56) Inner Flange (57) Figure C: Cut.Off Wheel Hardware 6. Replace with a new Cut.Off Wheel (56), and reassemble the parts listed above in number 5. The concave side of the Outer Flange (55) must face the wheel. While holding the Lock Pin (63), tighten the Socket Head Bolt (54) with the Hex Key (111a). 7. LOOSEN THE BOLT (112) and make sure that the Swing Guard (53) moves freely back into place before operation. SAFETY SETUP OPERATION MAINTENANCE Depth Adjustment Note: The Cutting Depth will need to be adjusted whenever a worn down wheel is replaced with a new one. 1. Loosen the Nut (15) on the Depth Adjustment Bolt (16) shown in Figure D. Figure D: Depth AdjustmentDepth AdjustmentBolt (16) Nut (15) 2. Turn the Depth Adjustment Bolt (16) to change the depth so that the wheel will not contact the base at any time during cutting. 3. After adjustment, tighten the Nut (15) against the Bracket (14) to lock the adjustment in place. Work Piece and Work Area Set Up 1. Designate a work area that is clean and well.lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working. 3. Secure loose work pieces using the vise to prevent movement while working: a. To use the Quick Release (31), put the Quick Release (31) tab in the position shown in Figure E and push the Vise Handle (28) up against the workpiece. Then tighten the Vise Handle (28). When releasing, loosen the Vise Handle (28) a few turns, lift up the Quick Release (31), and pull the Vise Handle (28) open. Figure E: Vise ComponentsVise Handle (28) Place Workpiece HereQuick Release (31) b. To cut at various angles (up to 45.), adjust the Angle Scale (35) by loosening the two Bolts (41 & 44) as shown in Figure F. Adjust the Angle Scale to the desired setting and then tighten the Bolts (41 & 44). Figure F: Angle ScaleBolts (41 & 44) AngleScale(35) Upper Two Screw Holes c. To reposition the Angle Scale (35), remove both of the Bolts (41 & 44), and reattach the Angle Scale at the upper two screw holes. See Figure E. 4. There must not be objects, such as utility lines, nearby that will present a hazard while working. General Operating Instructions TO PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED. Moving guards must move freely and close instantly. Bolt (112) MUST be loose before operation. 1. Using the vise, secure your workpiece and, if necessary, adjust the angle of the cut. 2. Raise the Saw by p...
Эта инструкция также подходит к моделям:Лобзики и пилы - 91938 (1.73 mb)