2 LOCK BUTTON -8 BM 2610917132 10-03 10/28/03 11:07 AM Page 9 Installing Power Corh !WARNING DIRECT CORD CONNECT ATTENTION: before inserting plug into SYSTEM HAS BEEN handle, always make sure you leave enough CONFIGURED TO BE USED WITH 12AWG cord at plug end to avoid tension on plug SJ CORD, MAXIMUM LENGTH OF 50 FEET. when inserted into tool. INSPECT THE CORD, DO NOT USE IF 3. Push end of plug through spring clip and DAMAGED. into female outlet in handle as shown below . 1. Loop cord as shown in

Many accidents are caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool, may become hazardous when used on another tool. Service Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. For example: internal wires may be misplaced or pin

To use the standard clamp, remove the quick change clamp assembly by unscrewing the set screw which holds it onto the draw bar. Then assemble the standard clamp with the screw and lockwasher provided. Operating Instructions VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed controlled trigger switch. The tool can be turned "ON" or "OFF" by squeezing or releasing the trigger. The blade plunger stroke rate can be adjusted from the minimum to maximum nameplate stro

Loosen the screws on the underside of the miter table attachment (approx. 1/2 turn). Also loosen the preset angle release button and locking screw if necessary. Align the saw blade of the mounted saw with the aid of a protractor or square to achieve the 0. setting. Tighten the thumbscrew to secure setting, then securely tighten the screws on the underside of the table attachment (Fig. 11). ALIGNING SAW BLADE 90. TO THE MITER TABLE ATTACHMENT If necessary, the blade can be re-aligned to be 90. to

Standards by Underwriters Laboratories. -5 This symbol designates that this tool complies to NOM Mexican Standards. Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. -6- Functional Description and Specifications ! WARNING Model number 1640VS Voltage rating 120 V 50 - 60Hz Amperage rating 3.5 A No load speed n0 2,000-2,800/min Maximum capacities Stroke length

Their thin kerf and tooth design deliver the best speed, quality of cut, and reduce battery drain. Use of standard blades will substantially affect the performance and reduce run-time. -8 BM 2610914527 3/03 3/18/03 10:47 AM Page 9 Assembly ATTACHING THE BLADE Do not use wrenches with longer handles, Disconnect battery pack since it may lead to over tightening of the from tool or place the blade stud. ! WARNING -9- FIG. 2 TIGHTEN LOOSEN BLADE STUD LOWER GUARD SPRING OUTER WASHER Large Diameter Fa

Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure. FIG. 11 FIG. 12 WRONG RIGHT RIP CUTS The combination blade provided with your saw is for both cross cuts and rip cuts. Ripping is cutting lengthwise with the grain of the wood. Rip cuts are easy to do with a rip fence (Fig. 13). To attach fence, insert fence through slots RIP BOARD GUIDE

!CAUTION The motor may stall if improperly used or overloaded. Reduce the pressure (feed rate) or depth of cut to prevent possible damage to the tool if the motor labors. TOOL PARK REST The park swings down to help keep the blade from coming in contact with the work surface when plane is not in use (Fig. 6). The tool park rest was designed to swing up and out of the way by it itself when the back of the plane crosses the leading edge of the workpiece (Fig. 7). FIG. 6 FIG. 7 ADJUSTING DEPTH OF CU

Removing the blade is essentially the reverse of the installation procedure, however, take note that once the blade change button is loosened, gently push the blade upward to release the blade tabs from the plunger. Operating Instructions SLIDE "ON-OFF" SWITCH The Tool is switched "ON" by the slide switch located at the side of the motor housing. TO TURN TOOL "ON": slide the switch forward. TO TURN TOOL "OFF": slide the switch backward. VARIABLE SPEED DIAL This tool is equipped with a Variable S

Underwriters Laboratories. This symbol This symbol designates that designatesThis symbol designates this tool is listed by that that this tool is listed by Underwriters Laboratories, this tool the Canadian Standards and listed to Canadian compliesAssociation. Standards by Underwriters to NOM Laboratories. Mexican Standards. This symbol designates that this tool is listed by Intertek Testing Services. -5 BM 2610956795 12-07 12/12/07 1:27 PM Page 6 Functional Description and Specifications !WARNIN