Оценок - 4, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
Chargers should not be left plugged in or charging for more than 2 hours. Operation Install saw blade. Prepare and secure the material to be cut before turning on saw. Battery should have a full charge before using saw. Refer to illustrations that follow. Remove battery before making any adjustments. Warning: Do not hold tool by the handle while making adjustments as your fingers may touch the Switch and Safe buttons and start the saw. Installing Cutting Blade 1. Remove battery. 2. Press on the stop button (#17) located on top of the saw to keep the saw blade from moving while turning the nut bolt. 3. Using the hex key (#48), loosen and remove nut bolt (#1) and washer (#2). 4. Rotate movable guard (#8) clockwise to allow entry of blade. 5. Insert saw blade through the base with teeth facing forward (and up) until the center holes of the saw blade and motor adapter (#5) align. (Notice the arrow on the movable guard and the arrow on the saw blade, they should be pointing in the same direction.) 6. Replace washer (#2) and nut bolt (#1). Tighten with hex key (#48) while pressing on the stop button (#17). Verify stop button is in the up (unlocked) position. 7. Replace key to its storage hole in the housing of the saw. Adjusting The Saw Prior to Cutting 1. To adjust the angle of blade up to 50°, loosen knob (#57) and move base plate (#50) down, observing the degrees indicated on the angle plate (#53). Tighten knob (#57). See illustration on next page. 2. To adjust the depth of the cut, loosen knob (#43, not visible) located behind motor housing, and move base plate (#50) down while observing the amount of saw blade exposed under base plate. Tight knob (#43). SKU 37412 Page 5 Rev 09/98 REV 05/02 37412.p65 5 10/7/03, 11:56 AM Knob (#43, not visible) Knob (#57) Angle Plate (#53) Battery (#14) Base (#50) Nut Bold (#1) Washer (#2) Guard (#9) Exhaust Hole Movable Guard (#8) Hex Key (#48) Safe Button (#45) Switch Button (#47) Stop Button (#17, not visible) Prepare Material Before Cutting 1. Support large panels to minimize risk of blade pinching and saw kickback. 2. Use a rip fence or secured straight edge guide when ripping material. 3. Securely clamp material to be cut to work bench. 4. Make sure saw does not cut into supports or workbench. 5. Use the appropriate type of blade for the material you are cutting. SKU 37412 Page 6 37412.p65 6 10/7/03, 11:56 AM Cutting Warning: this tool can cause serious injury if not used properly. Read this entire manual before using. Verify that saw blade is securely tightened and both angle and height adjustment knobs are tight. 1. Secure rip fence or straight edge to the material to guide the saw on a straight path. 2. Place the saw base (#50) on material to be cut. Align the front notch (right edge aligns with saw blade) on the cut line. 3. Pull the rear lock switch (safe button #45) back with the middle finger and squeeze the switch button (#47) with the index finger. Do this before the saw blade touches the material. 4. With the saw at full speed, move the saw slowly forward to complete the cut. 5. When the cut in complete, release the power switch button (#47). Do not set the saw down until the blade stops turning. Maintenance 1. Before remounting the saw blade, remove all sawdust that has accumulated around the guard (#9), nut bolt (#1), and washer (#2). 2. Regularly inspect all mounting screws and knobs to ensure that they are properly tightened. 3. Keep saw blades clean and sharp. Sharp blades minimize stalling and kickback. 4. Keep guards in good working order. 5. Keep motor air vent clean of dust and debris. Vacuum periodically. 6. If the tool is not operating normally, making unusual noises, or appears defective, stop using it immediately and get it repaired. 7. Clean tool with a damp cloth and light detergent. Do not use solvents as they can damage and crack the plastic parts. SKU 37412 Page 7 37412.p65 7 10/7/03, 11:56 AM #metInoitpircseDytQ1 tloBtuN1 2 rehsaW1 3 )dedulcniton(edalBwaS1 4 8*3MwercSdutS3 5 retpadA1 6 egnalF1 7 rehsaW1 8 drauGelbavoM1 9 )revocnoitcetorp(drauG1 0101*4MwercSdutS1 11ralloC1 21gnirpSecroFeugroT1 31esaCthgiR1 41411B-DYTyrettaB1 51pilCyrettaB1 61)eulb(eriWreppoC1 71nottuBpotS1 81ralliPnottuBpotS1 91gnirpSnottuBpotS1 0251v-wkhctiwS1 12001081gniraeBllaB1 22esaCxobraeG1 32gaDpotS1 42xoBgniraeBdnaraeG1 52elxAleehWtenalPdnatfahSniaM1 62raeGtenalP3 72recapS1 828*4MwercSdutS2 924recapS2 03xoBraeG1 138*4MwercSdutS2 23raeGrotoM1 33rotoM1 #metInoitpircseDytQ43)der(eriWreppoC1 53)kcalb(eriWreppoC1 63esaCtfeL1 7305*4MwercSdutS4 83esaBrotoM1 9352*9.2TSwercS2 0402*9.2TSwercS3 14esaCkcaB1 2421*9.2TSwercS2 34bonK1 44gnirpS1 54nottuBefaS1 64gnirpS1 74nottuBhctiwS1 84hcni8/1yeKxeH1 9408*6MtloB1 05esaB1 155leviR1 25raBediuG1 35etalPelgnA1 455leviR1 558*4MwercS2 6521*6MwercS1 75bonK1 85raBgnitcennoC1 95eldeeN1 065*3MwercS1 16elxA1 265MtuN1 3601*4MwercS1 464MtuN1 56tsoPrebbuR1 66)dedulcniton(ecneFpiR1 SKU 37412 Page 8 37412.p65 8 10/7/03, 11:56 AM Assembly Drawing SKU...