• Press the AUTO ON / PAUSE button to start slicing (Fig. 10); the PRODUCT TRAY moves back and forth at the speed and at the stroke length you have selected. • When done slicing, you can stop by pressing either the AUTO ON / PAUSE button or the OFF button (Fig. 10). Pressing AUTO ON/ PAUSE returns the PRODUCT TRAY to the home position (all the way toward you). • ••If you pressed AUTO ON / PAUSE, the KNIFE continues to run and the stoke length is retained in short-term memory for 30 seconds. If y

Carefully reassemble the plastic RING GUARD COVER by putting it in position using the three guide PINS (Fig. 14). Carefully reassemble the TOP KNIFE COVER (Fig. 13) by putting it in position over the plastic RING GUARD COVER using the three guide PINS. Secure both RING GUARD COVER and TOP KNIFE COVER by turning the LATCH KNOB (Fig. 7) counterclockwise while lowering the TOP KNIFE COVER; then release the LATCH KNOB and turn it clockwise until snug. Reassemble the SHARPENER by lowering it straight

Rotate to Vertical. Slide Fence Up. Model 2912B Fig. 1 Tighten Thumbscrew. ELECTRICAL WARNING: THIS MACHINE IS PROVIDED WITH A THREE-PRONG GROUNDING PLUG. THE OUTLET TO WHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. CLEAN BEFORE USING Thoroughly clean and sanitize the slicer after installation and before use. Refer to CLEANING, pages 6 –7. – 3 – OPERATION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE

CLEAN BEFORE USING The 2612 or 2712 slicer must be thoroughly cleaned and sanitized after installation and before being used. Refer to Cleaning, page 6. – 3 – OPERATION SAFETY SAFETY DEVICES INCORPORATED IN THIS SLICER MUST BE IN THEIR CORRECT OPERATING POSITIONS ANYTIME THE SLICER IS IN USE. The TOP KNIFE COVER must be in position and secured with the LATCH KNOB (Fig. 2). The RING GUARD is not removable. The DEFLECTOR, mounted below the slicer knife, can be removed for cleaning. The MEAT GRIP (

2006) Installation, Operation and Care of MODEL 6430, 6430T, 6460 & 6460T PEELERS SAVE THESE INSTRUCTIONS GENERAL Models 6430 and 6430T Peelers are designed to peel 30 to 33 lbs (13.5 to 15.0 kg) of product in 1 to 3 minutes using a 3/4 HP, single- or three-phase electric motor. The 6430T includes a synchronous timer and is available for single-phase electrical service ONLY. Models 6460 and 6460T Peelers are designed to peel 50 to 60 lbs (22.5 to 27.0 kg) of product in 1 to 3 minutes using a 1 H

Excessive pressure during sharpening could overheat the blade resulting in loss of temper and reduction of cutlery life. The unloader wheels prevent over-pressure (and over-heating) by lifting the blade off the belt if too much pressure is applied. INSTALLATION UNPACKING Immediately after unpacking the Knife Sharpener, check for possible shipping damage. If the BE1 is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery. Prior to ins

The CARRIAGE TRAY SUPPORT ARM is secured to the slicer by turning the KNOB below the SUPPORT ARM clockwise until snug (Fig. 2). Mount the SHARPENER on top of the slicer (Fig. 1) by lowering it onto its post. The SHARPENER can be removed for cleaning. The DEFLECTOR (Fig. 1) should already be mounted Fig. 1 below the knife. ELECTRICAL WARNING: THIS MACHINE IS PROVIDED WITH A THREE-PRONG GROUNDING PLUG. THE OUTLET TO WHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE IS NOT T

Dimensions, illustrations, technical data, weights, etc. are given as an indication only. || mioN 500 r c www.dito-electrolux.com

Dimensions, illustrations, technical data, weights, etc. are given as an indication only. || mioN 500 r c www.dito-electrolux.com

Main feature: removable peeling chamber and peeling plate. The peeling chamber fits easily onto the base, with the drive shaft fitting into the centre of the plate. User advantages: - possibility of loading the tank away from the peeling area - easily cleanable - suitable speed for shelfish cleaning FEATURES • Rotation speed, while preserving the mussels quality, allows the cleaning of 5kg. of shellfish in 2 minutes. • Seashells can be loaded directly into the peeling chamber, away from t