Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Excessive pressure during sharpening could overheat the blade resulting in loss of temper and reduction of cutlery life. The unloader wheels prevent over-pressure (and over-heating) by lifting the blade off the belt if too much pressure is applied. INSTALLATION UNPACKING Immediately after unpacking the Knife Sharpener, check for possible shipping damage. If the BE1 is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to assure that it agrees with the specifications on the data plate located on the right side of the housing. LOCATION The Model BE1 Knife Sharpener should be placed on a suitable counter, table, or workbench where the suction-cupfeet will hold the sharpener in place. ELECTRICAL CONNECTION WARNING: THE ELECTRICAL CORD IS PROVIDED WITH A THREE-PRONG GROUNDING PLUG. THE OUTLET TO WHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN . ELECTRICAL DATA Model Volts / Hz / Phase Amps BE1 120 / 60 / 1 0.4 OPERATION WARNING: DO NOT IMMERSE. UNPLUG BEFORE CLEANING, SERVICING OR REMOVING PARTS. REPLACE PARTS BEFORE USE. CONTROLS (Fig. 1) On – Off Switch — Turns the sharpener On and Off. Circuit Breaker — Breaks the circuit if the current exceeds 1 Ampere. Turn off sharpener. Then press Circuit Breaker button to restore circuit. On/Off Switch Circuit Breaker Adjustment Knob Adjustment Knob— Centers belt track when sharpener is on. PL-51362 Fig. 1 © HOBART CORPORATION, 1994 – 2 – SHARPENING KNIVES Guide Plate Guide Plate Clean and dry knife before sharpening. Turn sharpener on. Insert the knife in the sharpening area with the handle next to the housing. The knife should be flat against the guide plate (Fig. 2). Slide the knife down the guide plate until it contacts the unloader wheels. Move the knife smoothly and continuously to the right or left at a rate of one inch per second. Turn the knife over and repeat the procedure on the other side, moving the knife in the opposite direction. The first time a knife is sharpened on the BE1, you may need to repeat this procedure four or five times for each side of the knife. Once sharpened, only one pass-per-side should be required. MAINTENANCE WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. HOW TO REPLACE THE SHARPENING BELT (Fig. 3) Bottom Spring Refer to Replacement Parts, page 4. Tensioner Unloader Wheel Sharpening Belt Loosen the two knurled screws and remove the side panel. Press down on bottom spring tensioner to loosen the Belt; remove Belt from drive wheels. With the Sharpening Belt removed, the unloader wheels Drive Wheels PL-40083-1 can be replaced if worn or cut. To remove either unloader wheel, squeeze the shaft on the nylon pin and remove Fig. 3 both the wheel and pin. Assemble new parts as follows: 1) Insert a new nylon pin through the hole in the housing or side panel. 2) Assemble a new unloader wheel onto the shaft of the nylon pin so the wheel is snug to the side panel or housing. Install new Belt around two drive wheels. Press down on the bottom spring tensioner to position the Belt on the drive wheels. Replace the side panel with its two knurled screws. NOTE: When installing a new belt, turn the adjustment knob on the right side until the belt is centered. Assure that the belt is tracking in the center, not rubbing the housing. TROUBLESHOOTING PROBLEM SUGGESTED ACTION Won't run. Check electric power supply. Check On - Off switch. If tripped, press Circuit Breaker button. SERVICE For service problems related to this equipment, contact your local Hobart-authorized service office. Unloader Wheels PL-40084-1 Fig. 2 Tension Spring – 3 – FORM 18843 Rev. A (4-94) – 4 – PRINTED IN U.S.A. KNIFE SHARPENER UNIT ILLUS. PART PL-51462 NO. NAME OF PART AMT. 1 438336 Fastener - Drive ............................................................................................................................ 1 2 438328 Unloader Wheel ............................................................................................................................ 1 3 438475 Plate - Cover Assy. ....................................................................................................................... 1 4 438339 Foot - Suction ............................................................................................................................... 5 5 WL-14-5 Lockwasher 8 External Shakeproof .............................................................................................. 5 6 NS-11-12 Mach. Nut 8-32 Hex ..................................................................................................................... 5 7 SC-120-35 Mach. Screw 8-32 x 3/8 Phil. Pan Hd. .......................................................................................... 2 8 WL-14-5 Lockwasher 8 External Shakeproof ..........