Section III - Hazardous Ingredients (1) I M P O R T A N T ! This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal use of this product are covered by Section VII; see it for industrial hygiene information. CAS Number shown is representative for the ingredients listed. (1) The term “hazardous” in “Hazardous Ingredients” should be interpreted as a term required and defined in the Hazardous Products Act and does not nec

Require all operators to read this manual thoroughly before installing, operating or NOTE: servicing this equipment. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. To avoid electrical shock that can cause injury or death, always unplug the unit prior DANGER! to proceeding with any and all maintenance or cleaning procedures! Do not work around conveyor belt with long hair, loose clothing, or dangling jewelry. DANGER! Getting caugh

NOTE: Require all operators to read this manual thoroughly before installing, operating or servicing this equipment. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating WARNING: and maintenance instructions thoroughly before installing or servicing this equipment. This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible pers

Each oven deck contains two separate gas control systems with the following requirements: Gas control system has a manual shut-off valve, internal pressure regulator (factory preset at 3 .” water column/. 87 kPa or 8.70 mbar for Natural Gas), and an electric solenoid operated main gas valve. Heat is supplied by one (1) burner rated at 120,000 BTU/H. (126MJ) with electronic ignition. Natural Gas requires 7” WC/1.7 kPa or 17.4 mbar inlet with maximum allowable of 14.5” WC/3.6kPa or 36.05 mbar. Gas

• FastBake™ Panel Configuration - Designed specifically to produce a bake faster than any other model. • Tandem-joined Impinger® I ovens to optimized capacity and baking performance. • Each deck contains two independent heating systems. • Front doors allow access to chamber for easier cleaning. Specifications: General: Gas Fired Baking/Finishing Oven is self-contained, conveyorized and stackable up to 2 high. Temperature is adjustable from 250 F (121C) to 600 F (316C). Conveyor speed is adjustab

2. Press the Up or Down key until the value you want appears on the display. 3. Press the Cook Temp key again. The cooking temperature has been set. [`idle] will appear on the display. Set the cooking time: 1. Press the Cook Time key. [tinE1] and then the cooking time value will appear on the display. 2. Press the Up or Down key until the value you want appears on the display. 3. Press the Cook Time key again. The Cooking Time has been set. [`idle] will appear on the display. 26 n Watlow MINICHE

3. Remove wireway by taking out the (5) five hex screws. 4. Disconnect wiring from motor. 5. Remove the twelve (12) hex head bolts from the oven back and slide back straight out of the oven. 6. Remove two (2) bolts from fan hub and remove fan from motor shaft. NOTE: Measure distance from fan blade to rear wall assembly before removal to aid in reassembly. 7. Remove the eight (8) hex head bolts from the motor mount and slide the motor assembly out of the oven back. 8. Remove motor by taking off m

NAT. GAS MODEL 1451 120VAC 60 HZ. LP GAS POWER SUPPLY Electrical power is supplied to the oven by a three conductor cordset. Voltage from the black conductor to the white conductor is 120VAC. The white conductor is neutral. The green conductor is ground. CONTROL BOX AUTO When the temperature in the control box reaches 120°F ± 3° (48.9°C ± 1.7°C), COOL DOWN the cooling fan thermostat will switch power to the control box cooling fan. The thermostat will interrupt power to the cooling fan when the

and thoughtful operation on your part. DO NOT INSTALL, OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL AND THE SAFETY PRECAUTIONS CONTAINED THROUGHOUT. And, most importantly, think before you act and be careful. (button) (Stamp comment Rita Wood 07.06.2002 16:27:39 blank) R OPERATOR’S MANUAL World's Leader in Welding and Cutting Products Premier Manufacturer of Industrial Motors • Sales and Service through Subsidiaries and Distributors Worldwide • Cleveland, Ohio 44117-1199 U.S.A. T

Specifications and availability of optional features may have changed. THE LINCOLN ELECTRIC COMPANY The World's Largest Manufacturer of Arc Welding Equipment Cleveland 17, Ohio CONTROL PANEL 1 Rheostat 2 Rheostat Handle 3 Diverter Switch Blade & Handle 4 Diverter Switch Receptacle, 4th step 5 Diverter Switch Receptacle, 3rd step 6 Diverter Switch Receptacle, 2nd step 3,4, 5, 6 Diverter Switch Complete 7 Voltameter 8 Voltameter Switch 9 Voltameter Shunt 10 Push Button 11 Wing Nuts