Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Require all operators to read this manual thoroughly before installing, operating or NOTE: servicing this equipment. Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. To avoid electrical shock that can cause injury or death, always unplug the unit prior DANGER! to proceeding with any and all maintenance or cleaning procedures! Do not work around conveyor belt with long hair, loose clothing, or dangling jewelry. DANGER! Getting caught in the belt could result in serious injury. For your safety, do not store or use gasoline or other flammable vapors or liquids in DANGER! the vicinity of this or any other appliance. Do not spray aerosols in the vicinity of this appliance while it is in operation. DANGER! If the power supply cord appears to be damaged, do not attempt to operate the unit. DANGER! Contact a service agent or qualified electrician to repair! Do not use parchment paper when placing food product through the toaster! Use of DANGER! such materials may cause a fire and should never be placed in the toaster. BEFORE INSTALLATION Upon receipt of this unit, immediately unpack and inspect for possible concealed shipping damage. If the unit is found to be damaged, save all packing materials and contact your delivery carrier within 5 days. Refer to “Shipping Damage Instructions” enclosed for detailed instructions. Failure to follow these instructions will negate both Merco Savory’s and your ability to file claims and receive compensation for shipping damage. GENERAL INFORMATION The ST-1 “Mini-Toaster” is capable of one or two-sided toasting of a variety of bread products such as breads, buns, bagels, english muffins and raisin bread. The ST-1 is a horizontal conveyor toaster that has high production capabilities, yet is scaled down in size to accommodate operations with a minimum of counter space. The ST-1 is available in 120V, 208V, 220V and 240V models. All models are equipped with variable conveyor speed and an energy saver switch standard. ST-1 Mini-Conveyor Toaster Operator Manual INSTALLATION INSTRUCTIONS Install the ST-1 in the most convenient location for ease of cleaning, maintenance and general operation. Avoid installing in locations with drafts, close proximity to grease or vapor-producing appliances or other high ambient heat equipment. Allow approximately 1” clearance on sides and back of unit for proper air circulation. Allow sufficient overhead clearance for proper heat dissipation. This toaster must be level for proper operation and comes equipped with 1” adjustable legs for this purpose. Before operating this unit, be sure that the following two components are properly installed: 1. The reflector tray is installed below the lower heating elements before shipping. It merely slides under the conveyor. NOTE: Proper toasting cannot be performed without reflector tray installed. 2. The toast receiving tray is packaged separately and must be installed before operating this unit. For front delivery position, slide the receiving tray into the toaster cavity below the control panel, making sure the lipped end is towards the back. Place the lipped end over the two (2) protruding pins located at the rear of the toaster cavity. For rear delivery position, slide the receiving tray into the cavity from the back of the toaster and place the lipped end over the 2 protruding pins closest to the front of the toaster (See Figure 1). Use these two mounting pins for front delivery position. WARNING ! ! This toaster must be plugged into the proper voltage which is specified on the data plate located on the back panel of the toaster. Use of any other voltage or altering of plug will damage unit, void warranty and may cause injury. Toast receiving tray in rear delivery position. Toast receiving tray in front delivery position. ELECTRICAL SPECIFICATIONS Voltage(Volts AC) Amperage(Amps) Max. Power (KW) Frequency(HZ) Phase Cord (Attached) Plug(Attached) 120 14.8 1.7 50/60 1 3’ NEMA 5-15P 208 12.5 2.4 50/60 1 3’ NEMA 6-15P 220 9.6 2.1 50/60 1 3’ NEMA 6-15P 240 10.4 2.4 50/60 1 3’ NEMA 6-15P *220 9.6 2.1 50/60 1 3’ None *240 10.4 2.4 50/60 1 3’ None The circuit on which the receptacle is installed must be of adequate wiring size and sufficient capacity to meet the requirements indicated on the unit data plate and in accordance with the National Electrical Code and local electrical installation codes. * The 220V electrical information in the shaded area pertains to European models. The 240V electrical information in the shaded area pertains to United Kingdom models. ST-1 Mini-Conveyor Toaster Operator Manual CONTROL PANEL FEATURES MAIN POWER SWITCH This switch is located to the left of the panel and has three (3) positions: Stand-By, Off, and Full Power. It controls the power going to the conveyor system and the two (2) heating zones. When the switch is in the “Full” position, all available power is reaching the heating elements. When the switch is in the “Of...