En los ceBos en que se encuentre un tomecornente de pered de dos esogas, deberá INSTRUCTION MANUAL For Operation & Service MANUAL DE INSTRUCCIONES Para Operación Y Servicio Técnico IMPORTANT SAVE ORIGINAL PACKING and ORIGINAL CARTON In ease of return. IMPORTANTE CONSERVE EL ENVASE Y LA CAJA ORIGINALES en caso de devolución. POR FAVOR LEA Y CUMPLA TODAS LAS INSTRUCCIONES MEDIDAS DE SEGURIDAD IMPORTANTES PLEASE READ AND FOLLOW ALL INSTRUCTIONS IMPORTANT SAFEGUARDS When using your overhesd pr

1Rackmount DX-700 — Ensure that the DX-700 is properly installed in your equipment rack. (Chapter 3, “Rack- Mount Installation”) 256P/ N 26-0601004-02Quick Start GuideVisibly yoursBarco, Inc. 11101 Trade Center DriveRancho Cordova, CA 95670 • USAPhone:Fax: Technical Support: Customer Service Portal: Website: +1 (916) 859- 2500+1 (916) 859- 2515+1 (866) 374- 7878barco.com/esupportbarco.comHandlesTwo recessed handles are provided. Chassis weight depends on the number of modules installed. Softkeys

• When this equipment functions abnormally, such as smoke, smell, noise, immediately unplug and call for professional assistance. • Unplug the visual presenter or shut off the power when not in use. CONTENTS System Diagram:....................................................................... 1 Rear Panel Connections ............................................................ 1 Front Control Panel................................................................... 2 Specifications .............

This means that after switching off the display or after switching to a different memory scan mode, the value for contrast and brightness is restored to the calibrated position. - The calibrated position for contrast and brightness is determined by calibration of the video levels (see § 3.4 below). In case you feel unsatisfied with the current calibrated position, you need to repeat the calibration. The proper way to do this, is to use the automatic calibration routine. However, you can also man

How to use the controls 1. When the OSD is not on the screen, touch any of the soft touch keys. The front illumination is switched on for about 10 seconds. 2. While the illumination is on, touch the Enter touch key to display the main menu. It contains several submenus. 3. To open a submenu, use the Up or Down touch keys to select the submenu. Next, press the Enter touch key to open the submenu. 4. To exit from a submenu, use Up or Down to select EXIT. Next, press Enter . If you exit from the Ma

Sharp edged or hard articles are prohibited. The gathering of dew in the panel may occur with abrupt temperature or humidity changes. A stable environment condition is recommended. Keep the surface clean. No adhesives should be applied. Avoid high voltage and static charge. Wall mounting You can mount the panel to the wall instead of to the foot, by means of the supplied mounting plate. If you do not need to mount the panel to the wall, please skip this item. Step 1: Remove the panel from the fo

Nor this document, nor any part of it, may be reproduced or copied in any form or by any means - graphical, electronic, or mechanical including photocopying, taping or information storage and retrieval systems - without written permission of Barco © 2010 Barco N.V. All rights reserved. Table of Contents Table of Contents Preface ................................................................................................. 5 Environmental information............................................

• Reconfigure the resolution of your computer to make it less than or equal to the native resolution (1920 x 1200). Problem: Image has vertical flickering line bars. • Use “Clock” to make an adjustment. • Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD Display. Problem: Image is unstable and flickering • Use “Phase” to make an adjustment. Problem: Image is scrolling • Check and make sure the video signal cable (or adapt

ge 110/120V/60Hz • UL and CSA Approved • Limited lifetime warranty Model # Head Type Hi-Lo Switch Doublet Fresnel Fold Down Arm Lamp Changer Lumens Lamp Type (ships with) Carry Handle 120 Closed No Yes Yes No 3000 ENX No 122 Open No Yes Yes No 3000 ENX Yes 127-P Closed No Yes Yes Yes 4000 FXL No 120EB Closed No Yes Yes No 4000 FXL No 122EB Open No Yes Yes No 4000 FXL Yes 127H/LEB Closed Yes Yes Yes Yes 4000 FXL No 128-P Open Yes Yes Yes Yes 3000 ENX Yes 129-P Open Yes Yes Yes Yes 4000