Оценок - 5, средний балл: 4.8
(
)
)
|
Фрагмент инструкции
1Rackmount DX-700 — Ensure that the DX-700 is properly installed in your equipment rack. (Chapter 3, “Rack- Mount Installation”) 256P/ N 26-0601004-02Quick Start GuideVisibly yoursBarco, Inc. 11101 Trade Center DriveRancho Cordova, CA 95670 • USAPhone:Fax: Technical Support: Customer Service Portal: Website: +1 (916) 859- 2500+1 (916) 859- 2515+1 (866) 374- 7878barco.com/esupportbarco.comHandlesTwo recessed handles are provided. Chassis weight depends on the number of modules installed. SoftkeysSix softkeys activate functions or access menus. Softkey labels appear in the Touch Screen’s left- hand column. To operate, press the Touch Screen button, or the adjacent softkey. Touch ScreenThere are 3 ways to use the Touch Screen: 1) Press a button on the Touch Screen itself. 2) Press a softkey directly adjacent to a button in the Touch Screen’s left-hand column. 3) Use the arrows to move the cyan “focus” highlight. Then, press ENTER to activate. NavigationUse the arrows move the “focus” highlight, and to scroll lists. To activate a highlighted function, press ENTER. TEST PATPress to access the Test Pattern Menu, to assign test patterns to selected outputs. PRESETSPress to access the Preset Management Menu, to recall and manage presets. BLACKPress to take all outputs to black. Press again to restore the previous video. FocusThe cyan “ focus” can be moved with the Navigation buttons. Configure DX-700 Modules — Ensure that all modules are installed in the proper configuration. (Chapter 2, “Module Installation and Configuration”) Connect Sources and Signals — Ensure that all sources and signals are properly connected. (Chapter 3, “Signal Installation” ) 7Power On LEDs, Fiberlink — Turn on power to your LED walls and Fiberlink connections. 8Power On DX-700 — Turn on power to the DX-700 chassis. (Chapter 4, “ Power-Up Initialization” ) Calibrate Touch Screen — Adjust display brightness and calibrate the Touch Screen. (Chapter 4, “Using the Front Panel Display Adjust Menu” ) 9Run the Setup Wizard — Use the Setup Wizard to configure LED wall outputs and “groups. ” ( Chapter 4, “Using the Setup Wizard”) Run the Input Wizard — Use the Input Wizard to configure inputs, and assign them to LED outputs. (Chapter 4, “Using the Input Wizard”) 10Recall Presets — Recall the desired preset, and you’re ready to begin production. (Chapter 4, “Using the Preset Management Menu” ) 111234Fine Tune Inputs — Use the Input Management Menu to adjust brightness, contrast, color and more. ( Chapter 4, “ Using the Input Management Menu” ) Fine Tune Displays — Use the Display Management Menu to adjust contrast, gamma, Fiberlink and more. ( Chapter 4, “ Using the Display Management Menu” ) IMPORTANTThese three buttons do not work from within the Setup Wizard. The following list summarizes the overall DX-700 setup procedure. For error-free installation, always refer to the listed section in the User’s Guide. Factory Reset— The first time you use a DX-700, or after a DX-700 returns from a show, perform a Factory Reset. (Chapter 4, “Performing a Factory Reset”) IMPORTANTEnsure that you set up all outputs and configure all output groups. IMPORTANTEnsure that you save a preset after you configure each input. 13 RGBHV Monitor OutDVI Monitor OutUse the Monitor Output Menu to set resolution and video source. Both outputs show the same video. Expansion Lock OutFor external stacking configurations, provides sync and communications to additional DX-700s. System ModuleOutput ModulesInput ModuleEXP OUTDVI / EXP INRGBHV1 -HD/SDI -2Y / COMPC / PbPrLatchesUsed for precise insertion and removal. See the “Module Insertion and Removal” section. Expansion OutConnects input modules for external and cross- bank stacking configurations only. RGBHV InputAccepts RGBHV inputs up to QXGA (2048 x 1536), with a max. 240 MHz pixel clock. HD / SDI InputAccepts: • 2 x SDI• 2 x HD-SDI• 1 x SDI and 1 x HD-SDI• 1 x Dual HD-SDIDX- 700 Input Modules provide the system’s input, scaling, and mixing functions. Within each module, the input source is selected from among the various input connectors and scaled to the required size and position in the final display. Component InputAccepts Composite, S- Video and Component. See the “Format Connection Table.” DVI / Expansion InputAccepts single or dual DVI inputs, with resolutions up to QXGA ( 2048 x 1536) with a max. 240 MHz pixel clock. Each module provides three outputs, which can drive one (or more) attached displays from any portion of a selected source image. LED OUT 1LED OUT 2LED OUT 3LED OUT 1LED OUT 2LED OUT 3LED OutputsThree DVI- I type connectors are provided for DVI outputs. LED OutputsThree HDMI-type connectors are provided for NNI outputs. WARNINGOutput Module connectors use proprietary signals and pinouts. Do not connect the outputs to anything other than the inputs of Barco LED tiles. • Use the Setup Wizard to configure outputs and groups. • Use the Input Wizard to configure inputs. • Use the Input Management Menu ...