1B) S — For glass actuated one-hand operation (see Fig. 1 A) + = Model vintage starting with letter A To change with any major design changes 150 and 151= Model number with cold plate and up to eight post-mix valves # = Model variations — Customer options starts with B - = Cabinet finish S — Stainless Steel F — Fawn This dispenser has a dual purpose actuating lever. Fig. 1A One-hand Operation Fig. 1B Two-hand Operation For the easiest two-hand operation, remove the one-hand lever. This
A. Verify valve and schrader caps are tightened to specifications (see Step 6). PRE-FORMED INSULATION TIGHTEN VALVE CAPS TO SPECIFICATIONS SV3084 B. Place insulation over schrader valve cap and left side of valve. Position the tab between the mounting bracket and rear panel. SV3085 PLACE TAB BETWEEN VALVE BODY AND PANEL C. Fold insulation and hold against right hand side of valve while securing with electrical tape. Seal the line set insulation to the shut off valve insulation with electrical ta
Part Number 000002688 07/2007 Safety Notices When using or servicing a Flake / Chiplet Series Ice Machine, be sure to pay close attention to the safety notices in this manual. Disregarding the notices may lead to serious injury and/or damage to the ice machine. Throughout this manual, you will see the following types of safety notices: Procedural Notices When using or servicing a Flake / Chiplet Series Ice Machine, be sure to read the procedural notices in this manual. These notices supply helpf
(121.9 cm.) 55.0 in. (139.7 cm.) B1400 60 in. (152.4 cm.) 55.0 in. (139.7 cm.) The bin drain is exactly in the center of the bin. Part Number 000002688 Section 2 Installation Instructions Location of Ice Machine The location selected for the ice machine must meet the following criteria. If any of these criteria are not met, select another location. • The location must be free of airborne and other contaminants. • The air temperature must be at least 45°F (7°C), but must not exceed 110°F (43.4°C)
6. Remove top cover from float reservoir. QF2300 Shown Float Valve Removal 1. Place the toggle switch in the OFF position, turn off the water supply and disconnect electrical power to the ice machine. 2. Disconnect water supply line at float valve quick disconnect by depressing stainless steel lever. 3. Remove water float valve coil. 4. Depress coil and rotate 1/4 turn counterclockwise. 5. With coil wires attached, lift coil off enclosure tube. 6. QF0800/QC0700/QF2300 ONLY Rotate quarter turn fa
Disregarding the notices may lead to serious injury and/or damage to the ice machine. Throughout this handbook, you will see the following types of safety notices: WARNING Text in a Warning box alerts you to a potential personal injury situation. Be sure to read the Warning statement before proceeding, and work carefully. CAUTION Text in a Caution box alerts you to a situation in which you could damage the ice machine. Be sure to read the Caution statement before proceeding, and work carefully.
Remove rear grille 3. Loosen both hose clamps on condenser hoses. Remove hose from condenser outlet (top) 4. With cup/pail at the ready, remove hose from condenser inlet (bottom). Drain condenser and hose 5. Loosen both hose clamps on water regulating valve. Using utility knife, cut both hose ends to facilitate hose removal from barbed fittings on valve 6. Remove both hoses and discard 7. Remove 2 screws from gray plastic drain manifold (some machines have brass winged adapter) on back pane
C836-72-1 . C0836-72 . C0836-72-1 . C0836-72M . C0836-72-1M Standard Features: • Griddle top with 1" (25mm) thick steel plate. • Full-range valve control (-72) • Griddle control, with embedded thermostat sensor bulb Low to 500F (260C) (-72-1) • Stainless front and sides • Stainless steel front rail w/ position adjustable bar • 1 1/4" NPT front gas manifold • Can be connected individually or in a battery • 6" (152mm) high stainless steel stub back • 6"(152mm) chrome steel adj. legs Model C836-72-
C836-72-1 . C0836-72 . C0836-72-1 . C0836-72M . C0836-72-1M Standard Features: • Griddle top with 1" (25mm) thick steel plate. • Full-range valve control (-72) • Griddle control, with embedded thermostat sensor bulb Low to 500F (260C) (-72-1) • Stainless front and sides • Stainless steel front rail w/ position adjustable bar • 1 1/4" NPT front gas manifold • Can be connected individually or in a battery • 6" (152mm) high stainless steel stub back • 6"(152mm) chrome steel adj. legs Model C836-72-
Oven & 36" Cabinet 220,000 80 1220/508 C0836-72-1 72" Thermostat Control Griddle- w/ (2) 36" Cabinets 180,000 80 1350/612 C0836-72-1M 72" Thermostat Control Griddle - Modular Top 180,000 40 1120/508 Interior Dimensions: In (mm) Product Height Width Depth Oven 13-1/2(323) 26-/1/4 (667) 29 (737) Cabinet Base 20-1/2 (521) 32-1/4(819) 31 (787) Individual Burner Ratings (BTU/hr) Burner NAT. PRO. Griddle 30,000 Oven 40,000 35,000 Gas Pressure NAT. PRO. Min. Supply 7" WC 11" WC Operating 6" WC 10" WC G