• Low maintenance cost unmatched fluid section replacement cost • Equipped with Hero Uni-toolTM an all in one tool which is all you need to replace the fluid section • Stainless steel piston and cylinder sleeve for corrosion resistance and longer packing life • Long wear HytrelTM, and ThiokolTM impregnated leather packings • Industrial duty DC electric motor, fan cooled, and totally enclosed • New Flip ControlTM prime valve for positive shut off, also serves as an emergency pressure release • Qu

b) and place rear-facing on vehicle seat equipped with LATCH anchors. 3 For ease of installation, extend LATCH belt to its maximum length. 4 Hook connectors to vehicle lower anchors (fig. a). Pull connectors to be sure they are securely attached to the anchor points. (fig. b). 5 Press down firmly in center of car seat while pulling LATCH adjustment belt. (fig. c). 6 Pull front to back and left to right to check for secure installation (fig. d). Check that the lower anchorage belt stays tight and

Additional Information • Tether Storage • Body Support • Head Support • Harness Cover • Care and Cleaning • Aircraft Use • Second Hand Child Restraint Replacement Parts...........................................52 •Locking Clip •Instruction Manual Storage 3 IMPORTANT INFORMATION No child restraint can guarantee protection from injury in every situation, but proper use helps reduce the risk of serious injury or death. READ THIS MANUAL CAREFULLY. For recall information: Call the U.S

Press “OK” to select. 19 20 21 Press OK for Menu Use UP/DOWN tochoose, OK to select Zoom Menu Zoom In/ Move Zoom Out Back Press OK for Menu 17 Zoom Out Press “OK” to open Menu. Choose the Zoom option and press” Ok” to select it. Choose “Zoom Out” and press “OK” to select it. Monitor will return to live video screen if available. Zoom icon will not be visible on the status screen. The Zoom icon should appear at the top the status screen. Monitor will return to the live video feed if available. 22

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can

3. Thread LATCH through base belt path normally used for vehicle seat belt. Make sure that LATCH is UNDER tongue on base . Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached . 5. Tighten LATCH by pushing down hard on base and pulling the adjustment belt . 6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer . 7. Test infant restraint for secure

Do not put the Nursery Units inside a crib or playard. • Use ONLY with 110-120 volt AC electrical outlets. • Protect the AC adapter cords. Place them so they are not walked on or pinched by furniture or other items. • Allow for proper ventilation when units are in use. Do not cover the Nursery Units or such as a blanket. Do not place them in a drawer or in any location which would muffle the sound or interfere with the normal flow of air. • DO NOT immerse any part of the Nursery Units, Parent Un

. Make sure drain valve is open. • Start the engine. • Open the hydraulic ball valve to allow hydraulic fluid to flow to hydraulic motor. • Paint pump should start to pump material and you should notice material flowing out to prime valve. • Let the pump run until the material is flowing evenly out of prime valve. • Close the prime valve and unit should now build up with pressure. • Run the pump until paint flows smoothly from the gun, without spitting, release the trigger. • Adjust the pump to

sanitary 1 408b SLEEVE, oval 2 408c CABLE 1 410 257580 TRIGGER, w/magnet 1 411 257790 HOUSING, valve w/ overmold 1 413 197058 BRACKET, stem 1 414 107110 LOCKNUT 1 416 177538 STUD, trigger 1 417 15Y526 NUT, lock, m4 sst 1 420 15Y200 FASTENER, pan head, 6-32 x .188 sst 1 423 256228 CONTROL, board, transmitter 1 424 15Y201 NUT, battery, wedged 1 425 24F260 KIT, battery cap 1 425a CAP PLUG, battery 1 425b 108284 PACKING, o-ring 1 426 15X949 BATTERY, CR123A, lithium, 3 volt 1 427 15X950 PAD, foam, is

Connect black power lead (J) on motor control board to ON/OFF switch. 11. Connect white power cord conductor (D) to motor control board (24). 12. Connect 15/20A switch connector (X) to motor control board (24). 13. Connect potentiometer connector (C) to motor control board (24). 14. Connect Prime/Tool Fill/Recirculate reed switch connector (E) to motor control board (24). 15. Replace control panel (37) and tighten bottom two screws (61). Torque to 30-35 in-lb. 16. Connect display connector to mo