Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
3. Thread LATCH through base belt path normally used for vehicle seat belt. Make sure that LATCH is UNDER tongue on base . Belt must lay flat and not be twisted. 4. Hook Connectors to vehicle lower anchors. Pull firmly on Connectors to be sure they are attached . 5. Tighten LATCH by pushing down hard on base and pulling the adjustment belt . 6. NEVER put two LATCH connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle manufacturer . 7. Test infant restraint for secure installation as described in infant restraint “Final Safety Check” p.36. 8. Check that the LATCH stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service. 33 6.5 Reclining Infant Restraint/Base For your child’s safety, it is important that your infant restraint/base be properly reclined. Attached to the side of your infant restraint is a level indicator to help properly recline the infant restraint/base on the vehicle seat. Failure to properly recline the infant restraint on the vehicle seat increases the risk of serious injury or death. If the infant restraint is too upright, a child’s head may drop forward and cause breathing problems. If the infant restraint is too reclined, a crash could put too much force on a child’s neck and shoulders. The infant restraint must be properly reclined according to the following instructions. Check the level indicator. You must look straight on at the indicator. —If the indicator shows ONLY blue, the infant restraint is properly leveled. —If any orange is showing in the level indicator adjust the recline. 34 When using the base: . To lower the foot; pull down on the bottom of the foot to the desired setting to adjust the recline . To raise the foot; set the base on a flat surface, push in on the fingers on the baseand push down on the base to adjust the recline . If there is still orange in the level indicator when the foot is completely extended then place a rolled towel under the foot until ONLY blue shows . . . When using only the infant restraint, if there is still orange in the level indicator when the . infant restraint is resting on the vehicle seat then place a rolled towel under the infant restraint until ONLY blue shows . Readjust the vehicle seat belt as necessary to secure the infant restraint firmly in the vehicle seat. 35 Final Safety Check: Every time you drive with your child, PUSH DOWN on the top of the infant restraint slowly but firmly to make sure the vehicle belt does not lengthen at all and that the vehicle belt or LATCH is fastened very tightly around the infant restraint/base . . Holding the infant restraint near the vehicle belt path, TWIST AND PULL the seat forward and toboth sides to make sure the vehicle belt or LATCH does not lengthen or loosen and the infant restraint does not easily move . 36 7.0AdditionalInformation7.0AdditionalInformation 7.1 Airplane Use Install in an airplane the same way as in an automobile. Notify the airline ahead of time that you intend to bring the seat on board. Use only in forward-facing aircraft seat. Follow the flight attendant’s instructions about infant restraint placement. Do not use this infant restraint if the airplane seat belt does not hold the infant restraint tightly. 7.2 Storing LATCH 1. For ease of storing, extend LATCH to its maximum length. 2. Locate the storage bars on bottom of infant restraint base . 3. Fasten end of LATCH (without adjustment belt) onto storage bar. 4. Repeat step 3 for LATCH with adjustment belt. After fastening onto Storagebars . storage bar, pull on adjustment belt to make sure LATCH is securelyfastened. 5. LATCH storage should look like this when complete . Underside of base 37 7.3 Cleaning and Maintenance ! TO REMOVE AND WASH INFANT RESTRAINT PAD, follow instructions in “6.1 Positioning Harness Straps”, p. 26-27. Carefully remove the seat pad. Machine wash on delicate cycle and drip-dry. DO NOT USE BLEACH. Reverse steps to reinstall seat pad. Check that harness system is not twisted, and pull on harness system to be sure harness is securely reinstalled. ! INFANT RESTRAINT METAL AND PLASTIC PARTS may be cleaned by wiping with a mild soap and water solution. DO NOT USE BLEACH. Use of bleach may weaken plastic parts. ! HARNESS STRAPS may be spot cleaned or replaced. DO NOT IMMERSE THE HARNESS STRAPS IN WATER. Doing so may weaken the harness straps. ! BUCKLE may be cleaned with a damp cloth. ! DO NOT LUBRICATE the buckle. ! DO NOT USE INFANT RESTRAINT without seat pad. ! CONTINUOUS USE OF INFANT RESTRAINT MAY CAUSE DAMAGE TO VEHICLE SEAT. Use an infant restraint mat, towel or thin blanket to protect upholstery. 38 NotesNotes 39 ReplacementPartsReplacementParts To purchase parts or accessories in the United States for your Graco product, please contact us at the following: or 1-800-345-4109 40 Asiento de seguridad infantil /portabebes Manual del propietario LEA ESTE MANUAL GUARDE E...