Оценок - 3, средний балл: 4 ( )

Производитель: Graco Размер: 4.78 mb Название файла: Язык инструкции:

Connect black power lead (J) on motor control board to ON/OFF switch. 11. Connect white power cord conductor (D) to motor control board (24). 12. Connect 15/20A switch connector (X) to motor control board (24). 13. Connect potentiometer connector (C) to motor control board (24). 14. Connect Prime/Tool Fill/Recirculate reed switch connector (E) to motor control board (24). 15. Replace control panel (37) and tighten bottom two screws (61). Torque to 30-35 in-lb. 16. Connect display connector to motor control board (24). 17. Assemble display cover (33k). Spring tabs on noise shield need to be assembled to the inside of the control box enclosure. Torque screws (33b) to 30-35 in-lb. 18. Remove four screws (40) and lift motor shroud (98) off of motor. 19. Disconnect material hose (79) from pump (18a). 20. Replace Power Module, see page 7. ti15849a J ti15851a 24 D ti15850a X 24 ti15791a C 24 ti13572a E 24 ti15795a 37 61 ti13569a 24 33b ti15786a 33k ti15624a 98 40 ti15616a 79 18a Motor Control Board 18 3A0246C 110 UK and 240V Models: 1. Use acetone or equivalent cleaner to thoroughly remove thermal paste from pockets on heat sink. 2. Apply new thermal paste into both pockets of heat sink. 3. Replace two inner screws and washers to control board and torque to 17 in-lb. 4. Replace six outer screws to control board and torque to 11 in-lb. NOTE: SW1 position setting does not matter. 5. Connect motor control board lead connectors (F) to leads from motor. Insert grommet in heat sink baffle. Use zip tie or electrical tape (Z) to hold grommet together on grommet end on the motor side of the heat sink. 6. Assemble gasket (94) to heat sink assembly. 7. Assemble two screws (83) to hold motor control board/ heat sink assembly to power module frame. Torque to 35-45 in-lb. 8. Assemble ground screw (58) to heat sink. Torque to 30-34 in-lb. 9. Assemble control box enclosure (3) to power module using two top screws (61). Torque to 30-35 in-lb. 10. Connect blue (B) and black (G) power leads from motor control board (24) to filter board. ti14695a ti14693a ti15926a ti14697a ti15852a F Z 94 ti15911a ti15845a 83 ti15846a 58 ti15912a 3 61 ti15848a B G Motor Control Board 3A0246C 19 11. Connect potentiometer connector (C) to motor control board (24). 12. Connect Prime/Tool Fill/Recirculate reed switch connector (E) to motor control board (24). 13. Replace control panel (37) and tighten bottom two screws (61). Torque to 30-35 in-lb. 14. Connect display connector to motor control board (24). 15. Assemble display cover (33k). Spring tabs on noise shield need to be assembled to the inside of the control box enclosure. Torque screws to 30-35 in-lb. 16. Replace motor shroud (98) and torque four screws (40) to 30 - 34 in-lb. 17. Reconnect material hose (79) to pump (18a). 18. Replace Power Module, see page 7. ti15791a C 24 ti13572a E 24 ti15795a 61 37 ti13569a 24 ti15786a 33k ti15624a 98 40 ti15616a 79 18a Prime Valve Handle Prime Valve Handle Removal 1. Perform Pressure Relief Procedure, see page 4. Wait 5 minutes before servicing. 2. Use 3/32 in. punch and hammer to tap out handle pin (72c) (pliers may be required to pull out handle pin). Pull off handle (72a) and base (72b). 3. Use crescent wrench to unscrew prime valve (71). NOTE: Make sure that the seat and gasket are removed from the manifold. 72a 4. Clear out any material that is lodged in valve (71) or manifold (70). Installation 1. Tighten prime valve (71) into manifold (70). Use thread sealant on housing threads and torque to 190 to 210 in-lb. 2. Install prime valve base (72b). Pin in base must align with hole in manifold (70). 3. Orient hole in prime valve stem (71) vertically. 4. Place prime valve handle (72a) over prime valve base (72b) with handle in “apply” mode. Align hole in handle (72a) w/hole in prime valve stem (71). 5. Use hammer to tap prime valve handle pin (72c) back into place. ti15633a 72c 72b 71 70 20 3A0246C Pressure Transducer 3A0246C 21 Pressure Transducer Removal 1. Perform Pressure Relief Procedure, see page 4. Wait 5 minutes before servicing. 2. Remove four screws (33b) and cover (33k). 3. Disconnect transducer connector (E) from motor control board (24). 4. Disconnect potentiometer connector (D) and reed switch connector (87) from motor control board (24). 5. Remove four screws (61) and control box (3). Allow control panel (37) to hang down freely. 6. Remove grommet (23) from control box (3). 7. Remove transducer (39) and o-ring (50) from manifold (70). Remove grommet (23) from transducer and save for reuse. Installation 1. Install o-ring (50) and transducer (39) in manifold (70). Torque to 35-45 ft-lb (47-61 N•m). Install grommet onto transducer (39) and transducer into control box (3). 33k 33b ti15786a 24 E ti12999a 87 24 D ti15792a 61 37 3 ti15797a 61 ti15795a 3 23 ti15785a 23 39 50 70 ti15788a 3 70 50 39 23 ti15783a ti15793a Pressure Transducer 22 3A0246C 2. Connect transducer connector (E) and reed switch connector to control board (24). 3. Install control ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: