4. You can lock the Trigger in the ON position by squeezing the trigger, pressing in the Lock Button, and releasing the Trigger. The tool will operate continuously. To stop the tool, squeeze and release the Trigger. 5. Use only well-sharpened bits that are in good condition and appropriate to the task. 6. Use firm pressure when drilling, but do not press too hard. Too much pressure will cause the bit to overheat, may cause the bit to bend or break, cause undue strain on the tool, and may damage

Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. UNPACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 12 and 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. CLEANING, ASSEMBLY, AND MOUNTING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the

Moving parts can grab the surface and pull the tool out of your control. 6. Never leave this Air Hammer unattended when it is plugged into an air supply. Turn off the tool, and unplug it from an air supply before leaving. 7. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: Lead from lead-b

(See Figure C.) GEAR OIL PORT (210D) FIGURE C SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 8 OPERATING INSTRUCTIONS 1. WARNING! Always wear safety equipment. When operating the Impact Wrench, always wear ANSI approved safety impact eye goggles, hearing protec tion, heavy duty work gloves, sturdy work boots, and head protection. 2. Select the desired size socket (not included) and firmly insert the socket onto the 1” Square Socket Drive (188D). (See Figure A.) 3. Place the I

Keep the manual and invoice in a safe and dry place for future reference. SAFETY WARNINGS AND PRECAUTIONS 1. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. 2. KEEP CHILDREN AWAY FROM PRODUCT USAGE AREA. Do not allow children to handle this product. 3. DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not use this product. 4.

OF TORQl Motor Provides 2,300 RPM and 3, Convenient One-Touch Chuck for 50% More Compact Design: 5-3/4 Built-In L.E.D. Light Illuminates t r Added Muscle for Tough Jobs : Installation I Weighs Only 3.4 lbs. Makita built 4-pole motor delivers 1,330 in.lbs. of max torque; (0-2,300 RPM and 0-3,200 IPM) Best Fit Ergonoi Grip Shape <= Only 3.4 Ibs.with ergonomic grip Built-in L.E.D. light and one-touch chuck for simple bit insertion PERFORMANCE Models BTD141 BTD141Z LXT Li-Ion batteries

In some cases, due to variations in packaging, you may have to install the Spade Handle and Auxiliary Handle. Please refer to the assembly diagram on page 10. CAUTION: Be sure the tool is unplugged from any power source before performing any installation or adjustment of the tool. 1. Align the Spade Handle (31) with the Back Case (32). Insert the Spade Handle Knob (30) through the Spade Handle into the Back Case. Tighten the Spade Handle Knob by turning clockwise until tight. 2. Insert the Screw

Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Operation Impact Wrench For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. 1. You will need to prepare a 3/8” air connector (not i

All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions please call 1-800-444-3353 SPECIFICATIONS ITEM DESCRIPTION Net Weight 132 Lbs. Overall Height 33 - 1/4” Column Length (Head to Base) 18 - 1/4” Table Size 7 - 7/16” x 7 - 3/4” Speeds (12) 250, 340, 390, 510, 600, 650, 990, 1550, 1620, 1900, 2620, 3100 Swing Diameter 10” Motor Electrical Specificat

Page 4 SKU # 42976 FEATURES AND CONTROLS OF THE #42976 DRILL / MILL MACHINE 8 28 4 13 14 1516 17 18 5 12 191 9 20 6 7 3 2 3 10 11 9 23 25 2022 26 27 24 21 26 25 28 1. Column 2. Gear Strip 3. Head Crank 4. Vertical Head Lock 5. Chuck Feed Lever 6. Chuck Travel Limit Screw 7. Reference Scale 8. Chuck Fixing Lever 9. Chuck 10. Chuck Spindle 11. Chuck Spindle Collar 12. Motor 13. Drive Belt Cover 14. Motor Pulley 15. Transfer Pulley 16. Drive Pulley 17. Drive Belt Tension Lever 18. Drive Belt Tensio