Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
(See Figure C.) GEAR OIL PORT (210D) FIGURE C SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 8 OPERATING INSTRUCTIONS 1. WARNING! Always wear safety equipment. When operating the Impact Wrench, always wear ANSI approved safety impact eye goggles, hearing protec tion, heavy duty work gloves, sturdy work boots, and head protection. 2. Select the desired size socket (not included) and firmly insert the socket onto the 1” Square Socket Drive (188D). (See Figure A.) 3. Place the Impact Wrench on a firm stand or solid floor. 4. Set the Gear Change Lever (233D) to its “NEUTRAL” position. (See Figure A.) 5. Slide the Stop Button (103) upward to its “START” position. (See Figure A.) 6. Move the Throttle Assembly (102) to its “IDLE” position. (See Figure A.) 7. Press the Primer (161.1C) several times to force fuel into the Engine’s Carburetor. (See Figure A.) 8. Turn the Choke Lever (69) to its “CLOSED” position. (See Figure A.) 9. Pull sharply on the Recoil Starter (125B), and allow the Recoil Starter to return to its original position. (See Figure A.) 10. Once the Engine starts, slowly return the Choke Lever (69) to its “OPEN” position. (See Figure A.) 11. NOTE: Should the Engine fail to start, repeat Steps #6 through #9. 12. After starting the Engine, allow the Engine about 2 to 3 minutes to warm up before use. 13. WARNING! Before and during operation, always grip the Impact Wrench with both hands to brace for Engine torque. Also, maintain a firm stance to keep from slipping or falling down. 14. Insert the previously installed socket onto the bolt or nut that is to be loosened or tightened. 15. Use the Gear Change Lever (233D) to select the desired rotation (forward/ reverse) of the tool. Select “R” for clockwiserotation or “L” for counterclockwise rotation. (See Figure A.) SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 9 16. IMPORTANT: To avoid damage to the internal gears, do not change the rotation (forward/reverse) of the tool when accelerating the Engine. Change the rotation only when the Engine is at idle. 17. Squeeze the Throttle Assembly (102) for high speed to loosen or tighten the bolt or nut. (See Figure A.) 18. Once the bolt or nut is loosened or tightened, release the Throttle Assembly (102) to allow the Engine to return to idle speed. (See Figure A.) 19. Slide the Stop Button (103) downward to its “STOP” position. (See Figure A.) 20. Place the Impact Wrench on a firm stand or solid floor. Then, set the Gear Change Lever (233D) to its “NEUTRAL” position. (See Figure A.) 21. Allow the Engine of the Impact Wrench to completely cool. Then store the tool in a clean, dry, safe location out of reach of children and other unauthorized people. INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always make sure the Stop Button (103) is in its “STOP” position and the Spark Plug (3A) is removed prior to performing any service, maintenance, or cleaning of the Impact Wrench. 2. Before each use: Inspect the general condition of the Impact Wrench. Check misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect the safe operation of the tool. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Impact unit and Gear Case (209D) maintenance: Prior to each use, check the Gear Oil Port (210D) for proper gear oil level. If necessary, refill the Gear Case with #10 gear oil. (See page 8 and Figure C.) 4. Spark Plug (3A) maintenance: The condition of the Spark Plug should be checked every six months or 100 hours of tool use. If necessary, reset the gap and clean the old Spark Plug orgap and replace with a new Spark Plug. (See Figure D.) 0.025” SPARK PLUG FIGURE D (3A) SKU 95666 For technical questions, please call 1-800-444-3353 PAGE 10 5. Air Cleaner (78) maintenance: The Air Cleaner should be checked prior to each use of the Impact Wrench for excessive dirt and debris build-up. Thereafter, the Air Cleaner should be cleaned or replaced every three months or 50 hours of tool use. To do so, remove the cover of the Air Cleaner to expose the Air Cleaner Filter (74). Remove the Air Cleaner Filter and rinse the Filter in warm, soapy water. Squeeze the Filter to remove the soapy water, and allow the Filter to dry. Then replace the Filter and the cover of the Air Cleaner. (See Figure E.) AIR CLEANER FILTER (74) AIR CLEANER (78) FIGURE E 6. To clean the Impact Wrench: Use only a clean cloth and mild detergent. Do not use solvents as doing so may damage the finish of the tool. Do not introduce liquids into the internal parts of the Engine and Carburetor. 7. When storing the Impact Wrench: Before storing, drain all fuel out of the tool’s Fuel Tank. If this is not followed, old fuel in the Fuel Tank may clog the Carburetor and prevent the tool from starting until cleaned out. Then store the tool in a clean, dry, safe location out of reach of children and other unauthorized people. 8. C...