Refer to Operating Instructions-S witch. • Hold drill firmly to control the twisting action of the drill. If your drill is equipped with a side handle, always use the side handle. AWARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other m

The batteries can explode in a fire. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin - a.Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention

Other fasteners may not drive as well or hold as satisfactorily. 3. When using the screwdriver for the first time to drive screws into pressure-treated lumber, practice driving some screws in scrap material to get a “feel” and to adjust for proper seating depth. It will be significantly easier to guide and control the screw if 1/8" pilot holes are pre-drilled. This pre-drilling is recommended at the board ends to avoid splitting the lumber. 4. Once a screw has started driving, do not stop the

Use enough pressure to keep drill biting, but do not push hard enough to stall motors To minimize stalling on breaking through the material, reduce pressure on drill and ease the bit through last part of hole. 6. Hold drill firmly to control the twisting action of the drill. 7. THE DRILL STALLS if it is being overloaded or improperly used. RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of stalling. DO NOT CLICK TRIGGER OFF AND ON IN ATTEMPT TO START A STALLED DRIL

When servicing Double-Insulated Tools, it is extremely important that ONLY IDENTICAL REPLACEMENT PARTS BE USED and that REASSEMBLY OF TOOL IS IDENTICAL TO THE ORIGINAL ASSEMBLY. RAPID EXCHANGE HOME USE WARRANTY Black & Decker warrants this product for two years against defect in material and workmanship in normal residential use. This warranty does not cover damage resulting from negligent handling, misuse or lack of reasonable care. Please return the complete unit, transportation prepaid, to

A. | L DRILLING 1. Unplug the Drill when attaching or changing bits or accessories. 2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or hole saws. For METAL, use highspeed steel twist drill bits or hole saws. For MASONRY, such as brick, cement, cinder block, etc., use carbide-tipped bits. 3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use a wood “back-up” block to prevent damage to material. 4. Cent

Replace or repair damaged cords. EXTENSION CORDS CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS TOTAL EXTENSION CORD LENGTH NAMEPLATE — METRES RATING - AMPS 10 15 20 30 35 45 50 60 0-10.0 16 16 16 16 14 14 12 12 10.1-13.0 16 16 14 14 14 12 12 12 13.1-15.0 14 14 12 12 12 12 12 — Before using Extension Cords, inspect them for loose or exposed wires and damaged insulation. Make any needed repairs or replacement before using your power tool. CHUCK ON NON-REVERSING DRILLS UNPLUG DR

Try to keep this ratcheting to a minimum for longest clutch life and longer screwdriving capacity between charges. Always drill pilot holes for wood screws. Spraying all screws with a dry lubricant will glm them the east©«! rundown. Experiment with different types of sheet metal screws to find the ones best syited to your application. pi©«* ? ADJUSTING DEPTH — PEPTH-SSfiSnWI 8CRUQUMS; 1. Pull back Collar and screw Locator in or out as follows: a) For DrywaiS Screws, end of bit should exte

О = 3 »<•< §5- а,* 2. 3“ = Ф о л т~<Е Ф От э СЗ® О ® ^ ^ = Оф 18“ •«1° < 5 ® з* Оо-ш "7* г 5 ® 5S s°- >о§: > О О н 5 Z > Г“ О 30 СО > ■п гп 3 я т 55* С о СО ® Щ 5 » о. ► sa ai » о w с CD Sm Ф 3s If Si 5* о с » ф ? > » о 36<£ф-36 5 § 1 m 5 я (Q а з о. « ! ю “I ф g|°S 40 2 * 2.2 > -*• m J. о ^ Ш ъ ® ,5 S ш CQ м - гп 1 3 Я » га 3 Г ® < z 8з*о 3® о ¡и I 1^1 л 2: |s» ® Ф о 3 -t -t » !" со р О 2Го’ 3 о - ф СО Ф т О тш •