Оценок - 3, средний балл: 3
(
)
)
|
Фрагмент инструкции
Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. UNPACKING When unpacking, check to make sure all the parts shown on the Parts Lists on pages 12 and 13 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. CLEANING, ASSEMBLY, AND MOUNTING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 14. To Clean The Micro Mill/Drill Machine: 1. When manufactured, the Micro Mill/Drill Machine has a special rust-proof coating applied to its outer parts and should be removed prior to use. To remove the coating, use a clean cloth and a mild solvent. Then, lubricate all moving parts with a premium quality, lightweight machine oil. To Assemble The Micro Mill/Drill Machine: 1. The Lifting Hand Wheel, Longitudinal Feed Hand Wheel, Cross Feed Hand Wheel, and Fine Feeding Hand Wheel (parts #97) must be assembled prior to using the Micro Mill/Drill Machine. The four Wheels are each identical in size and shape, and must be properly attached to the Worm Shaft (part #61), the Lifting Screw (part #95), and the two Lengthways Screws (part #111). (See Figure B, and Assy. Diagram.) 2. To attach the four Wheels (parts #97) to the Micro Mill/Drill Machine, insert one wheel each onto the end of the Worm Shaft (part #61), the Lifting Screw (part #95), and the two Lengthways Screws (part #111). Then firmly secure each Wheel, using one Washer (part #67), and one Top Nut (part #68). (See Figure B, next page, and Assy. Diagram.) To Mount The Micro Mill/Drill Machine On A Workbench: 1. CAUTION: Make sure the Micro Mill/Drill Machine is mounted on a flat, level, sturdy, workbench surface capable of supporting the weight of the Micro Mill/Drill Machine, additional tools, accessories, and the workpiece. 2. NOTE: When mounting the Micro Mill/Drill Machine on a workbench, you will need four 3/8” diameter bolts of appropriate length, four lock washers, and four nuts (not provided). LIFTING HAND WHEEL (#97) LIFTING HAND WHEEL (#97) SPINDLE BOX (#24) HANDLE SHAFT (#87) HIGH/LOW SPEED KNOB (#124) CLUTCH LEVER (#65) CLUTCH LEVER (#65) FORWARD OFF REVERSE SWITCH (#125) SPINDLE BOX (#24) FINE FEEDING HAND WHEEL (#97) FINE FEEDING HAND WHEEL (#97) HANDLE SHAFT (#87) VARIABLE SPEED KNOB (#122) CHUCK (#132) CHUCK (#132) LONGITUDINAL FEED HAND WHEEL (#97) WORK TABLE (#105) WORK TABLE (#105) LONGITUDINAL FEED HAND WHEEL (#97) CROSS FEED HAND WHEEL (#97) FIGURE B 3. With assistance, position the Micro Mill/Drill Machine in the desired location on the top of the workbench. Use the four mounting holes in the Base (part #74) of the Micro Mill/Drill Machine as a template, and trace with a pencil on the top of the workbench four 3/8” diameter mounting holes . Then, temporarily remove the Micro Mill/Drill Machine from the workbench. (See Assy. Diagram.) 4. Where the four pencil marks are located, drill four 3/8” diameter holes completely through the top of the workbench. 5. Then, secure the Micro Mill/Drill Machine to the workbench, using the four 3/8” diameter bolts of appropriate length, four lock washers, and four nuts as mentioned in Step #2. MACHINE ADJUSTMENT INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 14. To Use The Adjustment Controls: 1. CAUTION: ALWAYS TURN OFF THE MICRO MILL/DRILL MACHINE, UNPLUG ITS ELECTRICAL POWER CORD/PLUG (part #128), AND WAIT UNTIL IT COMPLETELY STOPS RUNNING BEFORE MAKING ANY ADJUSTMENTS. 2. To adjust the height of the Spindle Box (part #24) to accommodate the workpiece being milled/drilled; turn the Lifting Hand Wheel (part #97) clockwise to raise the Spindle Box, and turn the Lifting Hand Wheel counterclockwise to lower the Spindle Box. (See Figure B, and Assy. Diagram.) 3. To lower and raise the Chuck (part #132); pull the Handle Shaft (part #87) down to lower the Chuck. Pull the Handle Shaft up to raise the Chuck. (See Figure B, and Assy. Diagram.) 4. To adjust the fine feeding mechanism; push in on the Clutch Lever (part #65) which is located on the Fine Feeding Hand Wheel (part #97). Turn the Fine Feeding Hand Wheel clockwise to bring the tip of the Chuck (part #132) up. Turn the Fine Feeding Hand Wheel counterclockwise to bring the tip of the Chuck down. The Fine Feeding Hand Wheel may be adjusted from 0” to 1-1/4” up or down. NOTE: For normal, manual feeding, make sure the Clutch Lever is pulled out. (See Figure B, and Assy. Diagram.) 5. To move the Worktable (part #105)to the front and to the back; turn the Longitudinal Feed Hand Wheel (part #97) clockwise to position the Worktable toward the front of the machine. Turn the Longitudinal Feed Hand Wheel counterclockwise to position the Worktable toward the back of the machine. (See Figure B, and Assy. Diagram.) 6. To move the Worktable (part #105) to the right and to the left; tur...