Single-wheel sideSweep Hose • Clean the skimmer, filter and pump basket, clearing debris that restricts water flow. • Check the hoses, connections and swivels for leaks that cause loss of water pressure. • Remove the blue restrictor disk from the UWF. • If an adjustable gate valve is installed on the booster pump or cleaner line, open it completely so water can flow freely to the Polaris. If count is more than 32 RPM: • Replace the blue restrictor disk in the UWF with the red restrictor. If the

English English English Fine Tuning the Polaris Cleaner When operating correctly, the Polaris vacuums and sweeps all surfaces, moving randomly throughout the pool. The surface module floats on the water’s surface recirculating clean, filtered water. The sweep hose and filter bag move across the pool floor collecting dirt and debris. Approximately every 15-25 seconds the Polaris will change directions. Pressure Relief Valve The pressure relief valve in the Quick Disconnect automatically releases

• New plumbing lines should be flushed out before installing the Polaris. • Do not handle the Polaris while it is operating. • Always remove the Polaris before swimmers enter the pool. • Disconnect the Polaris from the pool wall when cleaning or backwashing the pool filter. • After cleaning or backwashing, let the filtration system run for at least five minutes before re-connecting the Polaris. • Always remove the Polaris from the pool before chemical shock treatments. For customer service or su

• After cleaning or backwashing, let the filtration system run for at least five minutes before re-connecting the Polaris. • New plumbing lines should be flushed out before installing the Polaris. • The Polaris should not be used to remove plaster dust in new pools. • Never handle the Polaris while it is operating. • When not in operation, always use the handle to pick up the cleaner. • Always remove the Polaris before swimmers enter the pool. • Always remove the Polaris from the pool before che

• Verify that all suction lines are closed except the one utilized by the flow indicator. • Check hose cuffs and connections for leaks that cause loss of flow. • For dedicated suction line installations, adjust valve in equipment area that controls water flow to suction line until indicator is within the target area. Mark valves for reference. • For skimmer installations, turn knob on flow regulator clockwise until indicator is within the target area. If the indicator does not move into the targ

Contact an authorized Polaris dealer for more information. 45 ElbowVacuum Plate90 ElbowVacuum Plate StandardHoseVacuum PlateStandard Skimmer Deep Skimmer Shallow Skimmer Connecting the Hose 1. Set aside the leader hose with hose weight and standard hose with hose weight. 2. Connect remaining hose sections pushing cuffs securely together. 3. Attach standard hose with hose weight to end of hose. 4. Attach leader hose to same end. The leader hose connects to the Polaris. 5. Connect assembled hose t

Other connections are possible, but they require additional fittings (see Section B on page 4). The Polaris 380 is intended for use with a Polaris Booster Pump.You should have a licensed electrician install the cleaner’s booster pump. The booster pump must be installed according to the electrical codes applicable in your area. Improper installation can result in serious or even fatal injury. The following are important points to remember when installing and operating the Polaris 380. • Always tu

1. Mark the single-wheel side tire. 2. Turn pump on, hold cleaner below water level and count wheel revolutions for 1 minute. 3. Optimum speed should be between 28 and 32 RPM. Single-wheel SideSweep Hose If count is less than 28 RPM: • Check the filter screen in the Quick Disconnect for debris. • Clean the skimmer, filter and pump basket. • Check the hoses, connections and swivels for leaks. • If the cleaner is connected to a dedicated return line, adjust the 3-way diverter to increase water flo

The Polaris climbs best in pools without sharp angles or curves in the transition from the pool floor to the pool wall. Approximately every three minutes the Polaris 380 goes into back-up mode. This action pulls the Polaris away from pool obstacles and increases its random pattern. Thrust Jet Adjustment The thrust jet powers the direction of the Polaris. Factory position is eleven o’clock, but depending on the pool, other settings are helpful. Sweep Hose Adjustment The sweep hose should move in

Part # Description Qty No. Part # Description Qty No. Part # Description Qty 1 2 3 K16 C40 K5 All-Purpose Bag* 1 Screw, 10-32 x 3/8" SS Pan 20 Top 1 20 21 C10 C6 Tire, MaxTrax®* 3 Wheel, Large (No Bearings Incl.) 3 39 40 41 9-100-1018 10-112-00 6-500-00 Bag Collar 1 Restrictor Disks, Red and Blue 1 Universal Wall Fitting (UWF) 122 23 24 C65 C131 C16 Axle, Large (Rear Wheel Only) 1 Thrust Jet Kit 1 Idler Wheel, Small 1 4 5 6 A20 9-100-3105 B25 Float, Head 1 Sweep Hose Scrubber* 1 Orifice Tip w/Or