Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
1. Mark the single-wheel side tire. 2. Turn pump on, hold cleaner below water level and count wheel revolutions for 1 minute. 3. Optimum speed should be between 28 and 32 RPM. Single-wheel SideSweep Hose If count is less than 28 RPM: • Check the filter screen in the Quick Disconnect for debris. • Clean the skimmer, filter and pump basket. • Check the hoses, connections and swivels for leaks. • If the cleaner is connected to a dedicated return line, adjust the 3-way diverter to increase water flow. If count is more than 32 RPM, unscrew the Pressure Relief Valve until the proper RPM is reached. If an adjustable valve has been installed, adjust the valve to reduce the amount of water flow. English English English Fine Tuning The Polaris Cleaner When operating correctly, the Polaris vacuums, sweeps and scrubs all surfaces randomly throughout the pool. The climbing ability of the Polaris depends on the pool’s shape and water pressure or flow. The Polaris climbs best in pools without sharp angles or curves in the transition from the pool floor to the pool wall. Approximately every 3-1/2 minutes the Polaris 360 goes into back-up mode. This action pulls the Polaris away from pool obstacles. Thrust Jet Adjustment The thrust jet powers the direction of the Polaris. Factory position is eleven o’clock, but depending on the pool, other settings are helpful. Sweep Hose Adjustment The sweep hose should move in a gentle sweeping motion. To decrease the motion of the sweep hose, turn the sweep hose adjustment screw clockwise. PushesUnitLeftPushesUnitRight12693IncreasesClimbingDecreasesClimbing11 See Troubleshooting for other action adjustments. Routine Maintenance Cleaning the Filter Bag Detach the bag by releasing the prongs and removing the bag tie collar from the feed hose. Open the closure and dump out the debris. Whenever possible, empty the filter bag when it is half full, especially if the dirt load is sand. It is easier to empty the filter bag when it is dry. Alternate between two filter bags. When one becomes full, remove it and put on the clean bag. Backwashing the Pool Filter Always disconnect the Polaris from the pool wall before cleaning or backwashing the pool filter. After cleaning or backwashing, let the filtration system run for at least five minutes to flush out the return lines before re-connecting the Polaris. Storage and Winterizing Never store the Polaris in direct sunlight. When storing for the winter, drain out all the water (freeze damage is not covered by the warranty). Remove the UWF from the pool wall by attaching the Quick Disconnect and using pulling pressure to unscrew. In some cases, it may be necessary to use the UWF Removal Tool (part #10-102-00) available from participating Polaris dealers. Shown from opposite side. Exploded Parts Diagram Pool Wall To the Polaris Serial number English Exploded Parts Diagram Pool Wall To the Polaris Serial number English No. Part # Description Qty No. Part # Description Qty No. Part # Description Qty 1 2 3 9-100-1014 9-100-1152 9-100-1114 All-Purpose Bag* Housing, Turbine Upper Hub Cap 1 1 3 20 21 9-100-1116 C131 Wheel, Single-side Thrust Jet Kit 1 1 39 40 41 9-100-3008 6-500-00 6-504-00 UWF Connector Assembly Universal Wall Fitting (UWF) Filter Screen, UWF/QD 1 1 122 23 24 9-100-7008 B20 B15 Sweep Hose Barb Complete Adjust.Screw, Sweep Hose Sweep Attach Clamp 1 1 1 4 5 6 9-100-5107 9-100-1108 C10 E-clip, Stainless Steel Ball Bearing Tire, MaxTrax® * 10 8 3 42 43 44 6-505-00 9-100-3009 9-100-3006 O-ring, UWF/QD Pressure Relief Valve, white Quick Disconnect, UWF 1 1 125 26 27 9-100-3005 9-100-7170 9-100-7009 Base Weight Hose Clamp for WMS Jet Retainer 1 6 2 7 8 9 9-100-1008 9-100-1017 9-100-7011 Wheel, Double-side Belt Kit, Small and Large Shield, Bearing 2 1 3 45 46 47 9-100-3109 9-100-3102 9-100-3002 Hose Nut Feed Hose, 6 Foot Swivel, Hose 12 4 428 29 30 9-100-7014 9-100-1155 9-100-3105 Water Management (WMS) Housing, Turbine Lower Sweep Hose Scrubber* 1 1 1 10 11 12 13 14 15 9-100-1005 9-100-5125 9-100-1139 9-100-1010 9-100-3135 9-100-1007 Frame Screw, 8-32 x 1/2" SS Axle Block Kit, front and rear Belt Divider, Pulley Collar, Bag Tie Transfer/Drive Shaft 1 11 1 1 1 1 48 49 50 9-100-1206 9-100-1200 9-100-1202 Float, Feed Hose In-line Back-up Valve Case Kit, Back-up Valve 3 1 131 32 33 9-100-5132 9-100-7030 9-100-1002 O-ring, Timer/Feed Pipe Top and Base Assembly Feed Pipe/Timer Blank 1 1 1 51 52 53 9-100-1213 9-100-1204 9-100-3103 Collar, Back-up Valve Mechanism, Back-up Valve Feed Hose, 1 Foot 1 1 134 35 36 A20 9-100-1011 B10 Float, Head Sweep Hose Complete* Wear Rings* 1 1 7 16 17 18 9-100-5115 9-100-5130 9-100-1132 Screw, 8-32 x 3/4" SS Lock Washer, Axle Block Drive Train Gear Kit 4 4 1 54 ** Pressure Tester 1 37 38 9-100-7026 9-100-1240 Base Assembly Top Housing 1 119 9-100-1103 Turbine Wheel with Bearing 1 * Wear items not covered by warranty. English English Troubleshooting If the Polaris cl...