Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
English English English Fine Tuning the Polaris Cleaner When operating correctly, the Polaris vacuums and sweeps all surfaces, moving randomly throughout the pool. The surface module floats on the water’s surface recirculating clean, filtered water. The sweep hose and filter bag move across the pool floor collecting dirt and debris. Approximately every 15-25 seconds the Polaris will change directions. Pressure Relief Valve The pressure relief valve in the Quick Disconnect automatically releases water if the Polaris is receiving too much water pressure. It can also be used to regulate the movement of the cleaner. If the Polaris changes directions too quickly, adjust the pressure relief valve to slow the cleaner. Quick DisconnectFilter ScreenPreasure Relief ValveQuick DisconnectPressure Relief Valve Routine Maintenance Cleaning the Filter Bag Depress the buttons on the jet sweep assembly to release the bag. Turn the filter bag inside-out to remove the debris. Open frame completely and reattach bag. Cleaning the Filter Screen Filter BagJet Sweep AssemblyButtonFrame The filter screen inside the Quick Disconnect captures debris missed by the pool filtration system. To clean, pull it out, rinse it and press it back into place. Backwashing the Pool Filter Always disconnect the Polaris from the pool wall before cleaning or backwashing the pool filter. After cleaning or backwashing, let the filtration system run for at least five minutes to flush out the return lines before re-connecting the Polaris. Storage and Winterizing Never store the Polaris in direct sunlight. When storing for the winter, drain out all the water (freeze damage is not covered under the warranty). Remove the sweep jet assembly from the sweep hose and store it flat. Hang or lay the hoses straight. Remove all fittings from the return lines including the UWF. In some cases, it may be necessary to use the UWF Removal Tool (part #10-102-00) available from an authorized Polaris dealer. Troubleshooting If the Polaris cleaner regularly displays the following actions, adjustments may be necessary to restore performance. Refer to exploded parts diagram for part references. Action: Polaris does not clean the entire pool or runs slowly. Solution: 1. Verify that the pressure relief valve is releasing water. If it is not, clean or backwash the pool filter. 2. Check the filter screen in the quick disconnect and clean if necessary. 3. Verify that the float hose is the proper length. 4. Remove the surface module top. With the Polaris operating, verify that the randomizer tube is moving back and forth. If it is not moving: Turn off pump, disconnect hoses, look into the mechanism and locate the filter connector inside the randomizer tube. If it is covered with debris or algae, remove the connector chamber, cylinder, and piston. Pull out the randomizer tube and clean the filter connector. If the connector is clean, replace the piston. If it is moving: Watch the randomizer ball in the mechanism. If it does not move within 2 minutes, replace the randomizer tube and piston. 5. Verify that the water pressure is between 5 and 10 psi. A pressure tester (part #6-11300) is available through your participating Polaris dealer. Action: Solution: Action: Solution: Action: Solution: Action: Solution: Surface module dives under the water or leans to one side. 1. Straighten twisted hoses. 2. Lift surface module out of the water, empty it and then shake it. If water is still heard inside, remove the top, pull out the drain plug assembly and drain the module. 3. Adjust the pressure relief valve until the surface module levels off. 4. Verify that the water pressure is between 5 and 10 psi. A pressure tester (part #6-113-00) is available from an authorized Polaris dealer. The float hose remains coiled. 1. See “Polaris does not clean entire pool.” 2. Lay the float hose out straight in the sun to remove the coils. Surface module moves too fast. 1. Adjust the pressure relief valve until the surface module slows down. 2. 165/Super Turtle only: Remove one of the eyeball regulators and readjust the pressure relief valve if necessary. 3. Verify that the water pressure is between 5 and 10 psi. Bag does not stay on the pool floor. 1. Verify that the bag has been installed correctly. 2. Check for air bubbles around the jet body assembly. This may indicate air in the plumbing lines. 3. See “Surface module moves too fast.” English Exploded Parts Diagram English No. Part # Description Qty. 1a 1b 2 6-306-00 6-309-00 6-400-00 Surface Module Top, Granite Turtle Top Mechanism 1 1 1 3 6-407-00 Cylinder 1 4 6-413-00 Screw, Mechanism, #6 x 5/16" SS Sheet Metal, Blunt-end 4 6-411-00 Piston Assembly 1 6 7 8 6-409-00 6-403-00 6-406-00 Center Chamber Assy Randomizer Ball Filter Connector/Randomizer Tube Kit 1 1 1 9 11 6-408-00 6-507-00 6-305-00 Connector Chamber Drain Plug Assembly Body Bottom Assembly 1 1 1 12 6-301-00 Body Bottom Wheel Kit 5 13 ...
Эта инструкция также подходит к моделям:Бассейны - SUPER TURTLE 165 (2.1 mb)