Оценок - 5, средний балл: 4.6
(
)
)
|
Фрагмент инструкции
Single-wheel sideSweep Hose • Clean the skimmer, filter and pump basket, clearing debris that restricts water flow. • Check the hoses, connections and swivels for leaks that cause loss of water pressure. • Remove the blue restrictor disk from the UWF. • If an adjustable gate valve is installed on the booster pump or cleaner line, open it completely so water can flow freely to the Polaris. If count is more than 32 RPM: • Replace the blue restrictor disk in the UWF with the red restrictor. If the flow is still too high, unscrew the pressure relief valve until the proper RPM is reached. Note: The pressure relief valve should only be adjusted when a restrictor is installed. • If an adjustable valve is installed after the booster pump, adjust it to reduce the water flow to the cleaner. English English English Fine Tuning The Polaris Cleaner The Polaris 280 vacuums, sweeps and scrubs all surfaces randomly throughout the pool. Approximately every 3 minutes the cleaner goes into back-up mode. This action pulls the Polaris away from pool obstacles and increases its random pattern. Thrust Jet Adjustment The thrust jet powers the direction of the Polaris. Factory position is straight back, but depending on the pool, other settings may be helpful. Sweep Hose Adjustment The sweep hose should move in a gentle sweeping motion. To adjust, turn off the booster pump and turn the sweep hose adjustment screw. Turn clockwise to decrease the motion. Routine Maintenance Cleaning the Bag Remove the bag collar from the feed hose. Twist the bag connector until it disengages with a clicking sound from the feed pipe. Pull off the filter bag, open the closure and dump out the debris. To reinstall, align markings on connector and feed pipe. Click connector into position on pipe and reattach bag collar to hose. Empty the bag when it is half full, especially if the dirt load is sand. It is easier to empty the bag when it is dry. Alternate between two bags. Cleaning the Filters Bag CollarZipper Closure Always disconnect the Polaris before cleaning or backwashing the pool filter, and let the filtration system run for at least five minutes before reconnecting the cleaner. To clean the in-line filter screen, pull it out of the filter assembly, rinse it and press it firmly back into place Storage and Winterizing Never store the Polaris in direct sunlight. When storing for the winter, drain out all the water (freeze damage is not covered under the warranty). Remove the UWF from the pool wall by attaching the Quick Disconnect and using pulling pressure to unscrew. If necessary, use the UWF Removal Tool (part #10-102-00) available from any authorized Polaris dealer. For on-line support: Install dishedside outSerialNumberMADE IN USAMADE IN USA392318162115910241316143233256241513141926283734383336352178571112181920212217293120301715181932PoolWall 10-foot Hose10-foot Leader HoseTo ThePolaris 10-foot Hose5152525454575855564245464443474841402117181922171322749501717153 Exploded Parts Diagram English Exploded Parts Diagram English No. Part # Description Qty No. Part # Description Qty No. Part # Description Qty 1 2 3 K13 C40 K5 All-Purpose Zippered Bag* 1 Screw, 10-32 x 3/8" SS Pan 20 Top 1 21 22 23 C6 C65 C131 Wheel, Large (No Bearings Incl.) 3 Axle, Large (Rear Wheel Only) 1 Thrust Jet Kit 1 41 42 43 6-500-00 9-100-9001 10-108-00 Universal Wall Fitting (UWF) UWF Connector Assembly UWF Restrictor Kit 1 1 1 4 5 6 A20 9-100-3105 B25 Float, Head 1 Sweep Hose Scrubber* 1 Orifice Tip w/Orifice Tip Guard 1 24 25 26 C16 C30 C32 Idler Wheel, Small 1 Screw, 4-40 x 3/16" SS Pan 1 Screw, 6-32 x 1/2" SS Pan Head 1 44 45 46 6-505-00 9-100-9002 D29 O-Ring, UWF/QD Pressure Relief Valve, Black Quick Disconnect, UWF 1 1 1 7 8 9 B5 B10 B15 Sweep Hose Complete* 1 Wear Rings* 8 Sweep Hose Attach Clamp 1 27 28 29 C25 C36 K10 Spring for C36 1 Swing Axle Kit 1 Base with Bracket 1 47 48 49 D15 ** 48-080 Nut, Feed Hose Adapter Hose, 8-1/2" In-Line Filter Assembly 10 1 1 10 11 12 B20 K30 K20 Adjust. Screw, Sweep Hose 1 Feed Pipe with Elbow 1 Vacuum Tube 1 30 31 32 K25 K145 C80 Water Management System 1 Frame 1 Ball Bearings, Turbine 2 50 51 52 48-222 D10 D45 Screen, In-Line Filter Float, Feed Hose Feed Hose, 10 Ft 1 9 2 13 14 15 C66 C76 C45 Axle, Large (w/Sand/Gravel Grd) 2 Screw, 10-32 x 7/8" SS Pan 10 Lock Washer for C36 7 33 34 35 C83 9-100-7170 A40 Turbine Shaft Tubes 1 Hose Clamp for WMS 2 Turbine Shaft Shield 1 53 54 55 D20 D50 G52 Swivel, Ball Bearing Feed Hose, Leader, 10 Ft Back-up Valve Kit 2 1 1 16 17 18 C70 C60 C55 Axle Plate for C65/C66 3 Ball Bearings, Wheels 8 Wheel Screw, Plastic 4 36 37 38 C86 C120 C110 Drive Shaft Assembly 1 Hose for C110, 7-1/2" 1 Turbine Cover with Elbow 1 56 57 58 G54 G57 G53 Case Kit for G52 Collar, Back-up Valve Mechanism for G52 1 1 1 19 20 C64 C10 Wheel Washer, Plastic 4 Tire, MaxTrax®* 3 39 40 9-100-1018 10-112-00 Bag Collar 1 Restrictor Disks, Red and Blue 2 *Wear items not covered by warranty. ...