With a supply voltage (VP) of 14,4 V, an output power of 24 W can be delivered into a 4 W Bridge Tied Load (BTL), or when used as a stereo amplifier, 2 . 12 W into 2 W or 2 . 7 W into 4 W. Features · Flexibility - stereo as well as mono BTL · High output power · Low offset voltage at the output (important for BTL) · Large useable gain variation · Load dump protection · Good ripple rejection · A.C. short-circuit-safe to ground · Thermal protection · Low number, small sized external components · L

Features · Requires very few external components · Thermally protected · High output power · Reverse polarity safe · Fixed gain · Capability to handle high energy on outputs (VP = 0 V) · Good ripple rejection · No switch-on/switch-off plop · Mute/stand-by switch · Protected against electrostatic discharge · Load dump protection · Compatible with TDA1517 (except gain). · AC and DC short-circuit-safe to ground and VP QUICK REFERENCE DATA PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supply volta

51 3 English EN Contents 1 Important 4 Safety 4 Notice 4 2 Your car power amplifier 5 Introduction 5 What’s in the box 5 Overview of the main unit 5 3 Installation 6 Mount the amplifier in car 6 Connect speakers 7 Connect car audio 7 Connect power 7 4 Use your power amplifier 9 Select filter mode 9 Select LPF frequency 9 Adjust input level 9 Adjust bass boost 9 About the protector indicator 9 Replace fuse 10 5 Product information 10 6 Troubleshooting 11 4 Notice Environmental information All unn

Fig.8 IP as a function of VP. 0 300 200 100 0 4 VP (V) IP (mA) 208 12 16 MGD921 MGD922 60 Po (W) 40 20 0 (1) (2) (3) 8 1012141618 VP (V) (1) (2) (3) EIAJ. 10%. 0.5%. Fig.9 Po as a function of VP. Fig.10 THD + N as a function of Po. 10 1 Po (W) 10-1 10-2 MGD923 10 102 103 104 105 THD+N (%) 1 kHz f = 10 kHz 100 Hz Fig.11 THD + N as a function of frequency. 10 1 f (Hz) 10-1 10-2 MGD924 10 102 103 104 105 THD+N (%) 10 W 1 W 1998 Sep 23 11 Philips Semiconductors Product specification Philips Semicond

. See below illustration: EN 9 Adjust input level To ensure sound quality, adjust input level to match it with the car audio’s output voltage. 1 Check the line output voltage of the connected car audio. 2 Rotate INPUT LEVEL to select a matched voltage: 0.3V to 6V. Adjust bass boost To enjoy more bass sound: 1 Set FILTER MODE at OFF or LPF mode. 2 Slide BASS BOOST to 12dB position. Tip •• If BASS BOOST is set at 0dB position, no extra bass will be boosted. Note •• If FILTER MODE is set at HPF mod

25 W high efficiency car radio power TDA1563Q amplifier FEATURES • Low dissipation due to switching from Single-Ended (SE) to Bridge-Tied Load (BTL) mode • Differential inputs with high Common Mode Rejection Ratio (CMRR) • Mute/standby/operating (mode select pin) • Zero crossing mute circuit • Load dump protection circuit • Short-circuit safe to ground, to supply voltage and across load • Loudspeaker protection circuit • Device switches to SE operation at excessive junction temperatures • Therma

2 APPLICATIONS · Television sets · Home-sound sets · Multimedia systems · All mains fed audio systems. 4 QUICK REFERENCE DATA 3 GENERAL DESCRIPTION The TDA8928J is a switching power stage for a high efficiency class-D audio power amplifier system. With this power stage a compact 2 . 10 W self oscillating digital amplifier system can be built, operating with high efficiency and very low dissipation. No heatsink is required. The system operates over a wide supply voltage range from ±7.5 V up to ±3

40 W BTL quad car radio power TDA8571J amplifier FEATURES • Requires very few external components • High output power • Low output offset voltage • Fixed gain • Diagnostic facility (distortion, short-circuit and temperature pre-warning) • Good ripple rejection • Mode select switch (operating, mute and standby) • Load dump protection • Short-circuit safe to ground and to VP and across the load • Low power dissipation in any short-circuit condition • Thermally protected • Reverse polarity safe • E

General description The TDA8566 is an integrated class-B output amplifier which is available in several packages. TDA8566TH is contained in a 20-lead small outline plastic package. The TDA8566TH1 is a 24-lead small outline plastic package which is pin compatible with the I2C-bus controlled amplifier TDA1566TH for one board layout. TDA8566Q is a 17-pin DIL-bent-SIL package. The device contains 2 amplifiers in a Bridge-Tied Load (BTL) configuration. The output power is 2 . 25 W in a 4 W load or 2

усилителем) к разъемам для динамиков на устройстве. Это можетБлагодаря этому усилителю вы можете наслаждаться высоким • Внешний дистанционный контроллер управления громкостью. Alternate noise is heard. повредить активные динамики. качеством звука с мощными басами. Вариант 1. Подключение 1 динамика в монорежиме в “мостовой” Настройка уровня входного напряжения j POWER (GND/REM/+12V) • В целях повышения безопасности управления автомобилем • The power connecting wires are installed too close to the