Mount upper wall plate using two wood screws in the top template position marked in Step 1 (see Figure E). Step 6: Choose direction you want the gate to open, based on Figure F. WARNING: THE GATE SHOULD NOT OPEN OVER THE STAIRS. Position upper stop plate onto upper latch plate so that stop plate wall faces stairs, as show in Figure C. rj £1 Step 7: Locate upper latch with alarm and remove battery compartment door with Phillips head screwdriver. Install 2 AAA batteries (included) into

Keep this instruction manual for future reference. Tools required: Phillips head screwdriver (not included). For Technical Support Call 1 -800-268-6237 or E-Mail at customerservice@summerinfant.com AWARNING: This product contains small parts. Adult assembly required. Exercise care when unpacking and assembling product. For use with children birth and up. INSTRUCTION MANUAL_ SURE AND SECURE™ DELUXE WOOD WALK-THRU GATE Thank you for buying the Sure and Secure™ Deluxe Wood Walk-Thru Gate from

Insert 4 tension bolts into holes on outside and slide inward towards frame as far as possible. visit us at Note: Do not use more than 3 total Summer Infant, Inc. extensions per gate. Do not use 6 Blackstone Valley Place more than 2 extensions per side. Lincoln, ri 02S8u6leU2SA 1-800-268-6237 ©2003 Summer Infant, Inc. Summer Infant Europe, LTD. 20 Sparrows Herne Bushey, Hertfordshire WD23 1FX UK 44 (0)20 8420 4429 8/05

6. Locate the Door Control within sight of the door at a minimum height of 5 feet where small children cannot reach and away from all moving parts of the door. 7. Install the User Safety Instruction Label on the wall adjacent to the door control and the Maintenance Instruction Label in a prominent location on the inside of the garage door. 8. Upon completion of the installation, the door must reverse when it comes in contact with a one-inch high object or a 2x4 laid flat on the floor. 9. Do not

THIS DEVICE COMPLIES WITH FCC RULES PART 15. Operation of this device is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference that may be received, including interference that may Cause undesired operation Safety Rules............................................................................... 2 Features of Your Opener ........................................................... 3 Specifications ................

The hazard may come from something mechanical or from electric shock. Read the instructions carefully. Mechanical Electrical When you see this Safety Symbol on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the corresponding instructions. Read the instructions carefully. This garage door opener is designed and tested to offer safe service provided it is installed, operated, maintained and tested in s

¦ The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned. ¦ Periodic checks of the opener are required to ensure safe operation. ¦ The model number label is located on the back of your opener. Contents Safety alert symbol review ...........................................2 Install the lights and lens ..........................................19 Safety information and precautions ..............................3 Attach the manual release rope and handle.............

30, 31 Safety warnings.......................................................................................................................25, 27 Door hardware.......................................................................................................................Maintenance ...............................................................................................................................7, 24-27 Reinforcement requirements .............................................

4-5b Pre-Wired source and sensor wiring methods. 6 5 4 3 2 1 or 6 5 4 3 2 1 Source Sensor Red Green Power Head Dashed Line = striped wire Solid Line = white wire Wall Wall Ceiling 1/2" 2" Cover clips FIG. 4-9 Install rear cover. Insulated Staple Wire Nut CONNECTING TO POWER 5 Plug the operator into a properly grounded electrical outlet. (Fig. 5-1) • To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third (grounding) pin. This plug will only fit a gro

2-3). NOTE: For header bracket and bolts locate Bag 2from Box 1. NOTE: The bolts supplied in Bag 2 are designedto be used on pressure treated lumber. 2. Mounting the header bracket. • Hold header bracket against wall (Fig. 2-3). • Position bracket as shown. – Place center on vertical line. – Bottom edge on final height line. • Mark screw hole locations on wall. • Drill 3/16" pilot holes at each screw hole mark. – Fasten header bracket with 2 lag screws (provided) (Fig. 2-3). Header bracket must