Constructed with 2" or 13/8" insulation pressure bonded between two steel skins, these doors provide the ultimate in durability, strength and energy efficiency. Quieter than other insulated and non-insulated doors, Premium Value Stamped Steel doors are the best choice for homes with rooms adjacent to or above the garage. Available in two Carriage House emboss designs, short and long. To further accentuate the Carriage House appearance, these doors come standard with beautiful decorative hardware

CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the 2-strand bell wire. Connect one end to the receiver screw terminals (polarity is NOT required). Route wire along the channels and out the bottom as shown. Connect the other end of the bell wire to the two opener terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the push button control. Use insulated staples (not supplied) to secure bell wire between receiver and ope

Recovering System BIOS - switch 2 / pinpair 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (see "BIOS update" chapter). On The System BIOS executes from floppy drive A: and the inserted "Flash-BIOS- Diskette" restores the System BIOS on the mainboard. Off Normal operation (default setting). Reserved - switch 3 and switch 4 Switch 3 and 4 are reserved. A26361-D1522-Z120-3-6319 English - 15 Add

8 2 Program IntelliCode® 2 Remote to Powerhead ............................9 Programming HomeLink®, Car2U®, IntelliCode® 1 remotes or wireless keypads ................................................................................................................10 Reference 3 Typical Installed Illustrations ................................................................ 11-13 Powerhead & Rail Assembled View ............................................................ 11 Typical Sectional Door

Keyless Entry Transmitter 1 pc 2.6 x 12 screw 1 pc 2.6 x 6 screw (Batteries inside) 1 pc 2.6 x 25 screw 2. PROGRAM A KEYPAD TO THE RECEIVER You need to do the programming in order to add the keypad transmitter to the receiver. 1 2 3 Plug the receiver 18R (sold separately) into an electrical socket. Press and hold the learn button at the left hand side of the receiver. The red LED on the receiver will flash. Press the [4-digit PIN], [#] and [the assigned number of the door] within 5 seconds. The

3 Parts Check List............................... 4 Assembly and Installation ....................... 5 Operation.................................... 5 Warranty..................................... 6 Parts Price List................................ 15 Method of Payment............................ 16 Illustrations................................... 19 Guide d’utilisation Introduction.................................. 7 Liste des Pieces............................... 8 Montage et installation.....

“OFF-ON” will prevent inadvertent operation of the door from any other push button, radio or keyless entry device. It will also as additional protection from unwanted operation during absence of the owner. This feature is to be activated only when the door is at the full open or close position and never while the door is moving. 2. “LIGHT” button allows the convenience light to be turned on and stay on until turned off by a second push of the button or activation of the door cycle. 3. “UP/DOWN”

6. Locate the wall console: • Within sight of the garage door, • At minimum height of 5 feet so small children are not able to reach it, and • Away from all moving parts of the door. 7. Install the Entrapment WARNING Label next to the wall console in a prominent location. 8. After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor. INFRARED PROTECTION FUNCTION 1. When garage door is opening, its moveme

For proper functionality, the limits must be learned during the installation process. The programmed limit process uses a combination of buttons on the control board. The specific buttons used for programming depends on which side of the gates the control box is mounted on and how many operators the installation includes. Refer to pages 11-12 to determine if the gate is Left- or Right-handed and for explanation of PULL-TO-OPEN and PUSH-TO-OPEN. If a mistake is made during the programming process