For use only with sectional doors. Homelink® and Car2U® compatible For Answers and Assistance: 1.800.354.3643 or visit SAVE THIS MANUAL FOR FUTURE REFERENCE Installer: Leave this manual with homeowner. PN# 37026500123, 2/26/2010 REV.1 Homelink® is a registered trademark of Johnson Controls Technology Company. Car2U® is a registered trademark of Lear Corporation. © The Genie Company 2010. X900-786 Models 2022/2024/2042GARAGE DOOR OPENERS ALWAY S AT YOUR COMMAND Includes: 2-Bulb Light System Wall

If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8). CAUTION Use 5/16"-18 x 1/2" Bolts FIG. 1-5 Rail - Power head assembly. FIG. 1-6 Chain adjustment. Chain Pulley Bracket (at wall end of rail) Chain T-Rail at center of rail assembly 1/8" T-Rail Chain Tighten nut to move pulley this direction Use 1/2" socket on adjustment nut Set assembled power head and rail aside. Begin with Section 2 INSTALLATION. Assembly for BELT DR

2. You can quickly press and release the "Close Travel Limit" button to move the door in small increments. You can also use the "Open Travel Limit" button to move the door slightly in the UP direction. 3. Door is fully closed when the bottom edge of door presses firmly onto the ground. 4. Once the door is in the desired position, press and hold the "Close SET Limit" button for 5 seconds. The LED indicator light will blink green once. This stores the closed position in memory. C) OPEN TRAVEL LIMI

1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including wall console, remote, or wireless keypad. 3. During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the rail carriage by pulling the Emergency Release Handle. See page 19 for Release Handle operation. LOST OR STOLEN REMOTE - CLEARING MEMORY Clearing rem

WARNING PN# 3642036534, 02/26/2010 REV. 1 1 2 3 41 2 31 2 WHITE BLANC BLANCO BLACK NOIR NEGRO GREEN VERT VERDE TRANSFORMER TRANSFORMATEUR TRANSFORMADOR PRIMARY PRIMAIRE PRIMARIO BLACK NOIR NEGRO BLACK NOIR NEGRO YELLOW JAUNE AMARILLO WHITE BLANC BLANCO BLACK NOIR NEGRO RED ROUGE ROJO BLACK NOIR NEGRO HALL SENSOR CAPTEUR DE PASSAGE SENSOR DE PASILLO YELLOW JAUNE AMARILLO MOTOR MOTEUR MOTOR GREEN VERT VERDE RED ROUGE ROJO RED ROUGE ROJO GREEN VERT VERDE WHITE BLANC BLANCO BLUE BLEU AZUL ORANGE ORA

Set the UP force level at the minimum force required to open door without stopping. 4. Once the desired level is selected, this stores the maximum force level for the UP direction in memory. ERASE - OPEN/CLOSE TRAVEL LIMIT 1. Press and hold both of the "SET" buttons ( SET & SET ) together until the green indicator light blinks (about 5 seconds). 2. All close and open travel limit settings are erased. Then follow the steps above to reprogram close and open travel limits. NOTE: The opener will not

Contact door distributor or manufacturer for instructions. HIGH SPRING TENSION Can Cause Serious Injury or Death Repairs or adjustments must be made by a trained service person using proper tools and instructions CHAIN CHAIN BELT BELT PN# 36420Supplement, 10/27/2008 9 1 OPENER ASSEMBLY FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM NOTE: Three (3) piece rail assemblies are for a 7 foot high door. Clear a workspace area to unpack and organize box and contents for assembly. 1. There are 4 boxes i

• It must be away from any moving parts. (You should NOT be able to reach the garage door while standing at Wall Button.) • Wall Button board screw connections are polarized, (+) positive and (-) negative. 2a. Wiring (If pre-wired). • Locate Wall Button pre-wired wire ends (Fig. 3-1). (They should be located within the guidelines mentioned above.) • Split and strip ends of wire (Fig. 3-2). • Fasten wire to Wall Button board screws on back of Wall Button. – Striped wire to the + (plus) terminal.

If the system engages with the door in the open position, personal items that are left unattended in the garage or home are at risk to theft. To insure the safekeeping of these items, close the garage door. Typical signs of an engaged system: Single spring system: Visually inspect the TorqueMaster® Plus right hand end bracket to confirm that the system has engaged (see illustration). If the system is engaged then the door will not close. If the opener force settings were properly set during the

Follow the instructions on this page. ATTENTION If your garage door opener has a Serial Number sticker which looks like this, in which the first two numbers are 10 or higher, your opener will operate using this Series III wall control. MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator IC: 2133A-CSD1D 120V. 60HZ. 5A FOR HELP CALL 1-800-35GENIE OR WWW.GENIECOMPANY.COM S/N:10XXXXXXXXXXXX Wall consoles from other manufacturers may not work with openers of these serial numbe