Оценок - 5, средний балл: 4.6 ( )

Производитель: Vermont Casting Размер: 882.07 kb Название файла: Язык инструкции:

• Swing the assembly against the firebox, and close the latches firmly against the pins protruding from the firebox top. Install ON/OFF Switch (R Models ONLY) The switch assembly parts are found in the parts bag. 1. Attach switch assembly to left rear side of stove shroud using two screws and existing holes in shroud. (Fig. 40) 2. Run wires down back of stove, under bottom of rear shroud to valve. 3. Attach wires to valve terminals. (Fig. 41) Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters Switch Existing Assembly Holes Screws ST315 Fig. 40 Attach switch assembly to rear shroud. PILOTADJ TP THTPTH ST228 Fig. 41 Attach switch wires to valve. Install the Front Plate Grasp the Front Plate and lift it into position, engaging the two steel tabs at the upper corners behind the adjacent bosses in the Side Plates. (Fig. 42) Seat the Front against the Sides so that the tabs at the bottom lip engage with the notches in the edge of the stove base. When properly installed, the bottom of the Front Plate cannot be pulled away from the sides without also lifting it up. If you are installing optional Warming Shelves, do so now, according to the instructions supplied with that kit. Thermostat Connection (Optional) R Models Only Use only a thermostat rated for 500 - 750 millivolts. Check the table below for the appropriate gauge thermostat wire to use for the length of lead required in your installation. Thermostat Wire / Gauge Maximum Run 18 40 feet 20 25 feet 22 16 feet 1. Install the wall thermostat in the desired location and run the wires to the stove location. Terminate these leads with 1/4” female connectors. 2. Connect the thermostat wires to the valve. (Fig. 41) This completes assembly of the PDV20 and SDVR stove. ST407 Bottom Tabs Engage Notch in Base Fig. 42 Install Stove Front. Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters Install the Log Set Remove the logs from their packaging, and inspect each piece for damage. DO NOT INSTALL DAMAGED LOGS. 1. Install the rear log by centering it side to side on the sheet metal shelf at the back of the firebox. (Fig. 43) The log will touch both sides and back wall of the firebox. 2. Install the right log by placing right side of log on burner so it is just touching firebox side. Lay log flat on burner almost touching the decorative grate. Then tilt log back so that it leans against rear log. (Fig. 43) Only the topmost part of the left side of log will touch the rear log. The right log sits freely on the burner and does not use locator pins to stay in place. 3. Place left log on burner, making sure to engage locator pins in holes in bottom of the log. (Fig. 43) This log does not touch any other log. 4. Sprinkle lava rock on burner in front of, and between, left and right logs. (Fig. 44) Right Log Rear Log Left Log Decorative GrateLG138 Fig. 43 Install back, right and left logs. Decorative Grate Lava Rock LG139 Fig. 44 Place lava rock on burner. Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters Operation Piezo Ignitor Button Pressure Tap The Stardance is operated with the operable door front plate in place with the doors open or closed. To open the front doors, insert the handle into the door latch stub and turn it to the left and up. (Fig. 45) When not in use, the handle may be stored in the handle holder on the right side of the rear shroud. (Fig. 46) Clockwise to Open Counterclockwise to Close ST621 Fig. 45 To open the front doors, turn handle clockwise. Handle Holder ST624 Fig. 46 When not in use, store handle in the handle holder. Your First Fire Read these instructions carefully and familiarize yourself with the burner controls shown in Figure 47. Locate the pilot assembly, Figure 48. Follow the lighting instructions on Page 28 exactly. PILOT ON OFF PILOTADJ LO HIRegulator Control Knob Gas Control Knob Pilot Adjustment Screw TPTH TH TP HV104 Fig. 47 RN & RP valve control. Pilot Assembly ST476a Fig. 48 Pilot Assembly location. Flame & Temperature Adjustment For stoves equipped with HI/LO valves, flame adjustment is accomplished by rotating the HI/LO adjustment knob located near the center of the gas control valve. (Fig. 49) During the first fire, it is not unusual to smell some odor associated with new logs, paint and metal being heated. Odors should dissipate within a few hours. You can open a window to provide fresh air to alleviate the condition. Pilot and Burner Inspection Each time you light your heater check that the pilot flame and burner flame pattern are as shown in Figures 50 through 52. If flame patterns are incorrect, turn the heater off. Contact your dealer or a qualified gas technician for assistance. Do not operate the heater until the pilot flame is correct. Follow regular maintenance procedures as described on Page 36. Turn counterclockwise Turn clockwise to decrease to increase flame height flame height Fig. 49 Flame adjustment knob for Honeywell valve. Flame Characteristics It is important to periodically perform a visual check o...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: