Войти:
Оценок - 2, средний балл: 3 ( )

Инструкция по эксплуатации Kathrein, модель MobiSet 2 CAP 210

Производитель: Kathrein
Размер: 1.79 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Safety instructions - important notes Safety precautions during installation During installation of the turntable, make sure that no persons, in particular children, are in the immediate vicinity of the turntable and that they do cannot touch any moving parts – danger of crushing! Always unplug the power supply during installation work. Lowering the antenna while driving While driving, the antenna must always be lowered to the horizontal position (park position). To remind yourself of this, please use the stickers in the visual area around your vehicle ignition switch. Cleaning the antenna To clean the antenna, use only water and cleansing agents typically used for vehicles. Do not clean the equipment with steam jet or high-pressure washers. Do not use any cleansing agents which contain solvents such as acetone, nitro-cellulose combination thinner, naphtha, etc. since this can damage individual components. Instructions for installation and operation of the HDP 171 with the UFD 170 1. The turntable can only be used in conjunction with a Kathrein UFD 170 Caravan Digital Combi Receiver or a Kathrein UFD 540 Caravan Digital Receiver with HDS 160 control unit. 2. To ensure reliable functioning of the turntable, the power supply cable must be connected directly to the battery. If the power supply is too low, the receiver indicates this with the on-screen message “On-board voltage too low!” or with “HDP overload” on the television screen. A fuse (15 A) is integrated into the power supply cable. Safety instructions - important notes If the fuse responds, the source of the fault must be eliminated. The defective fuse should only ever be replaced with a fuse of the same rated value. Never remove or bridge the fuse in the cable or in the receiver (UFD 170)! Cable fi re hazard! 3. Connecting the power supply cable lead marked “Ignition” activates the turntable function for automatic lowering of the antenna. This lowering takes place as soon as the vehicle ignition circuit is turned on. When connecting the control unit to the on-board network, it must be ensured that the “+12V”, “Earth” and “Ignition” wires cannot be broken by switches connected in series, as this can deactivate the automatic lowering function. Exceeding the normal vehicle height by not lowering the antenna increases the risk of accidents! The driver is responsible for the condition of the superstructure and external fittings! 4. While downloading software for the UFD 170 satellite combi receiver, the caravan ignition may not under any circumstances be turned on as this can result in impairment, faults or loss of function. Never turn off the receiver (UFD 170) during the update process, as otherwise you could lose the entire software. You would then need to re-install it at a service centre or using a PC and null modem cable. 5. Note on satellite search: If the vehicle is not on supports during the satellite search process and people are moving around inside it, there is a danger that the oscillations of the vehicle will mean that the satellite cannot be found. It should also be ensured that the vehicle is not oscillating when software download via satellite, as otherwise the download may fail. 6. For installation, the turntable HDP 171 may be used in conjunction with the UFD 170 in manual mode (see “installation and connection”, “installation of the BAS 60 planar antenna” sections). After installation of the BAS 60 planar antenna, the HDP 171 must be put in the park position with the reset command. The reset command can be accessed via the receiver menu (menu element “HDP antenna set-up”). Only then is the HDP 171 released by the software for automatic searching. This concludes the installation of the HDP 171. The instructions in the installation and operating manuals for these devices and for the extensions and superstructures must absolutely be heeded! Installation and connection Required tools and equipment • Circular cutter, O 38 mm • Flat-bladed screwdriver for M5 screws • Drilling machine • Galvanised tallow drop screws, depending on roof structure (O: 5 mm, sheet metal screws D 7981, depending on roof panel structure) or tallow drop screws D 7985 with shims and nuts • Twist drill, O 2.5 or 5.5 mm • Round file and/or emery paper • Cleaning agent • Fork or ring bolt with width of 10 and 11 mm • Knife • Cross recess screwdriver for M3 and M5 screws • Torque wrench between 6 and 11 Nm • Hexagon socket screw key (5 mm) • Two wooden beams for supporting turntable Unpacking and preparation Remove the turntable from the packaging. Retain the original packaging, as if it is necessary to send the unit for repair transport damage cannot be ruled out and the manufacturer accepts no liability for possible damage. Loosen the six fastening screws (width: 10 mm). Carefully lift the turntable off the mounting plate and place it on the prepared support beams. It must be ensured that the cable running out of the underside of the turntable is not crushed. Selecting...

Эта инструкция также подходит к моделям:
Спутниковые ресиверы - CAP 210 (1.79 mb)
Спутниковые ресиверы - MobiSet 3 CAP 310 (1.79 mb)
Спутниковые ресиверы - CAP 310 (1.79 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории