Оценок - 4, средний балл: 5 ( )

Производитель: Kathrein Размер: 1.79 mb Название файла: Язык инструкции:

A) and apply the sealing glue evenly to the underside of the roof duct flange. Replace the roof duct in the drilled hole and press it firmly against the roof of the vehicle. • Apply the sealing glue evenly to the underside of the mounting plate, covering the whole area between the grooves (Fig. D). This area must be completely glued onto the roof of the vehicle, in order to achieve the necessary adhesive force. Place the mounting plate on the roof of the vehicle, as you have done already when marking the drilled holes. Make sure that the arrow on the mounting plate points forward in the direction of travel. The fastening holes must be perfectly aligned with the prepared holes in the roof. • Fasten the mounting plate in place with the prepared screws, making sure that all six screws are evenly tightened across the diagonals. Note: The sealing glue used is capable of bridging small gaps caused by the curve of the vehicle’s roof. However, you should ensure that the mounting plate is not bent by tightening the screws. • Remove any sealing glue that leaks out at the sides with a clean cloth or if necessary with Sikaflex® Remover (available from specialist dealers). Do not use a cleaning agent or thinner containing solvents, as this could damage the sealing glue applied under the mounting plate. Only wash your hands with washing paste and water. • Secure the cable duct by counter-tightening the knurled nuts supplied from inside the vehicle (Fig. A). • Note that the setting of the sealing glue depends on the ambient temperature and the humidity. Final strength is reached after approx. five days. However, it is possible to carry out further installation work with no problems, as the mounting plate is held in place by the tightened screws. Installation and connection Installation of turntable Version with cable duct below turntable (Fig. E) Figure: E • Check that the O ring is correctly positioned in the groove of the cable duct (Fig. A). An incorrectly positioned or missing O ring will allow water to penetrate. • Feed the ends of the cables with the connectors as far as possible through the cable duct into the interior of the vehicle. Do not step on the connectors or kink the cables! • Lift the turntable and place it carefully on the mounting plate in the direction of travel. The through holes on the turntable must be perfectly aligned with the threads on the mounting plate. When lowering, make sure that the cables are fed through the cable duct and are not crushed. • Apply a little sealing glue to the six threaded holes in the mounting plate and screw the fastening screws into the thread. Tighten the screws to a torque of 6 Nm. • To prevent water vapour from inside the vehicle reaching the turntable through the roof duct, place the three cables in the sealing gasket supplied and insert them as far as possible into the roof duct. Make sure that no tensile loads are acting downwards on the sealing gasket as this can cause it to fall out over time. Installation and connection Version with external cable duct (Fig. F) Figure: F *) (not included) • Arrange the cables in the cable duct when placing the turntable onto the mounting plate. Make sure that the cables are not crossed over and that they are tightened so that they cannot be kinked. Do not try to pull the cable out of the unit. This could damage the cable or loosen the cable connections. • Place the turntable carefully on the mounting plate. The through holes on the turntable must be perfectly aligned with the threads on the mounting plate. • Apply a little sealing glue to the six threaded holes in the mounting plate and screw the fastening screws into the thread. Tighten the screws to a torque of 6 Nm. • The connecting cables should be fed into the interior of the vehicle through a waterproof cable duct.). The cables may not be crushed, kinked or damaged. The connecting cables between the turntable and the connecting/ control unit may not be extended! .) These watertight cable ducts exist in the area of boating and yachting technology, for example, so-called “cableports” and they can be purchased in boating and yacht outfi tting stores. Installation and connection Brief instructions for installing the HDP 171 The other detailed instructions in this operating manual must also be followed! For ease of illustration, we have dismantled the BAS 60 on these photographs. As supplied, the BAS 60 is pre-mounted on the HDP 171. The sequence of pictures shown illustrates all the necessary installation steps that are required to assemble the HDP 171 turntable and the BAS 60 planar antenna on the roof of the vehicle. Determination of installation location. Caution! System has a turning range of 96 cm (O). Drill hole with O 38 mm. Deburr sharp edges of hole. Apply Sikaflex® 291 adhesive to roof duct supports. Insert supports into hole and secure from below with knurled nuts. Unscrew screws (x6, SW 10) in mounting plate and remove mounting plate. Place turntable on prepared s...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: