Torque the three set screws (B, D) to 9-11 ft. lbs. 2 Gear Case Kit Installation Instructions Assemble Housing 1. Install the side covers (A, Figure 4) and secure with the original hardware. 2. Reinstall the bearings (C), washers, and retaining rings (D) in both side covers. Figure 4. Assemble Housing A. Side Cover B. Housing C. Bearing D. Washers & Retaining Ring Fill Auger Gear Case Oil 1. Remove the fill plug (Figure 5). Fill the gear box with The Dealer Line Winter Weight Worm G

1687227 & 1687228 Instructions For 2004 Simplicity 860EI Intermediate Snowthrowers W 1694433, 1694434 Kit Contents: Ref Part No. Qty. Description 1 1721684 1 GEAR CASE, RH 2 7090052 6 WASHER, 1/4” SPLIT LOCK 3 7092129 12 WASHER, FLAT, .268 x .591 4 7091576 6 NUT, HEX, 1/4-20 5 7092125 6 SCREW, HEX, 1/4-20 x 7/8 6 1721676 1 GASKET, GEAR CASE 7 1721685 1 GEAR CASE, LH 8 960625 1 FITTING - PIPE PLUG 4 Figure 1. Contents This kit is to service intermediate snowthrowers. INSTALLATI

14 727291 SCREW, 5/16-18 x .63 15 727940 SCREW, 1/4-20 x 2.00 16 727517 PLATE, Mounting Support 17 722305 SUPPORT, Frame 18 722320 FRAME, R.H. 19 722633 SCREW, 5/16-18 x 3/4 20 1740032 RING, Foam 21 724068 CLAMP, Fuel Line, Screw Type 22 723210 SCREW, 1/4-20 x 5/8 Footnotes: 522 SINGLE STAGE SNOW THROWER Manual No. 7006053 SERIES 0 TP 400-5245-IR-SX-N 13 Engine Drive System Group Manual No. 7006053 522 SINGLE STAGE SNOW THROWER TP 400-5245-IR-SX-N SERIES 0 14 Engine Drive System Group Item Part

7006053 Copyright © 2006 Briggs & Startton Corporation Milwaukee, WI USA. All Rights Reserved Revision IR, 11/22/2006 TP 400-5245-IR-SX-N Table Of Contents s PAGE GROUP 4 Handle Assembly Group 6 Body Covering Group 8 Auger and Housing Group 10 Chute System Group 12 Frame and Fuel Tank Group 14 Engine Drive System Group 18 Wheel Assembly Group 20 Electric Starter Group 22 Decals Group 522 SINGLE STAGE SNOW THROWER Manual No. 7006053 SERIES 0 TP 400-5245-IR-SX-N 3 Handle Assembly Group Manual No.

If done, the flywheel may shatter during operation. Do not tamper with links or other parts to increase engine speed. Regular maintenance improves performance and extends engine life. More frequent service is required when operating in adverse conditions. See any authorized service dealer for correct replacement parts. Other parts may not perform as well, may damage the engine, result in injury, or void your warranty. Inspect / Change Spark Plug (^Fig. 7^) Annually or every 50 hours of use

MS-3395-5/05 PRINTED IN U.S.A. Note: (This note applies only to engines used in the U.S.A.) Maintenance, replacement or repair of the emission control devices and systems may be performed /Gr'') by any nonroad engine repair establishment or individual. However, to obtain no charge repairs under the terms and provisions of the Briggs & Stratton warranty statement, any service or emission control part repair or replacement must be performed by a factory authorized dealer. Figures (Example: Fig.

. Fill tank to approximately 3.8 cm (1-1/2 in.) O below top of neck to allow for fuel expansion. If fuel spills, wait until it evaporates before starting engine. Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. STARTING ENGINE Fig. 4 CAUTION: The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will

1695196 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors This kit is required when installing front mounted snowthrowers. 2 Installation Instructions Sub-Frame Hitch Early Manual Lift Only (See Instructions) Hydraulic Lift 47 16 28 27 25 33 40 41 39 38 37 36 43 51 42 33 25 29 29 29 28 28 27 50 17 13 11 14 9 12 13 11 19 18 21 20 10 24 23 7 8 9 9 22 15 9 25 49 22 31 30 30 25 27 28 27 33 25 34 32 3 2 1 4 5 6 33 25 28 25 27 26 27 28 35 Front Hole for Doze

Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D F E Figure 7. Install Lock Plate - Hydraulic Lift Models A. Lift Cylinder D. Lock Plate B. Flat Head Pin (Original) E. Hair Pin Clips C. Flat Head Pin (New) F. Lift Shaft Assy. 5 6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E.