Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D F E Figure 7. Install Lock Plate - Hydraulic Lift Models A. Lift Cylinder D. Lock Plate B. Flat Head Pin (Original) E. Hair Pin Clips C. Flat Head Pin (New) F. Lift Shaft Assy. 5 6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E. Clamp Plate C. Hitch Rod Install Hitch 1. Slide the hitch under the tractor. 2. Raise the rear of the hitch and place the hook (C) over the lift shaft. 3. Connect the front of the hitch to the tractor J-hooks (A, Figure 8) using the hitch rod (B) and a safety clip in the top holes of the push bar latch. 4. Secure the front of the hitch to the tractor by attaching the hitch rod (C) and a safety clip in the bottom holes of the push bar latch. 5. Push the clamp plate (D) backwards until it is snug against the lift shaft. Tighten the clamp plate hardware (E). Sub-Frame Hitch Installation Instructions A C B D Figure 9. Install Lift Lever A. Lift Lever B. Lift Shaft C. Safety Clip D. Clevis Pin A C B Figure 10. Install Lift Rod - All Models A. Lift Lever B. Lift Rod C. Clip Install Lift Rod 1. Slide the lift lever (A, Figure 9) onto the end of the tractor lift shaft (B) under the right side footrest. 2. Use the tabs on the lift lever (A) to capture the tractor lift arm. Secure in place with a clevis pin (D) and safety clip (C). 3. Insert the rear of the lift rod (B, Figure 10) into the bottom of the lift lever (A). Secure with a clip (C). Install Reflectors 1. Install the two reflectors on the rear of the tractor seat deck. 7 Installation Instructions Sub-Frame Hitch REMOVAL NOTE: After removing components, reinstall the clevis pins and clips to prevent loss. 1. Disconnect the lift rod from the attachment and lift lever extension (C, Figure 11). 2. Remove the clevis pin and clip from the lift lever (C) and remove the lift lever. 3. Remove the front hitch rod (A) and (B). Remove the hitch and hook (F). 4. Remove the lock plate (E) OR reposition the lift link (D) in mowing position. NORMAL INSTALLATION 1. Insert the hook (F, Figure 11) into the back of the hitch. Mount the rear of the hitch on the lift crossshaft. 2. Secure the front of the hitch to the J-hooks using the hitch rod (A) and (B) (Figure 8). 3. Install the downward pressure lock plate (E) OR place the lift link (D) in snowthrower position. 4. Install the lift lever extension (C). 5. Install the lift rod and attachment (Figure 10). Figure 11. Normal Installation & Removal B C D E F A. Hitch Rod B. Hitch Rod C. Lift Lever Extension D. Lift Link (Manual) E. Pressure Lock Plate (Hydraulic) F. Hook Snowthrower Position A 8 Sub-Frame Hitch Installation Instructions A F C D G A B C D E Snowthrower & Dozer Applications Mower Applications A B C D F E A B F G E Snowthrower & Dozer Applications Mower Applicatio...
Эта инструкция также подходит к моделям:Снегоочистители - 1600 (719.25 kb)
Снегоочистители - 1700 (719.25 kb)
Снегоочистители - 2800 (719.25 kb)