Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Typical Spark Plug Connection File was named: 181-1275-14MY060105x.fm 2. Be sure fuel fill cap is on and tightened securely. See Figure 46. Figure 46. Fuel Fill Cap 3. Be sure you find the correct oil drain plug location (see equipment manufacturer’s instructions). See Figure 47. 4. Clean area around oil drain plug. Figure 47. Oil Fill/Drain Locations STOPSTOP1. Oil Fill Cap/Plug 2. Oil Drain Plug 2 2 Back View 1 2 Angled Front View 1 Page 20 4-Cycle • Snow King Engine 181-1275-14 5. Place approved recyclable oil container under oil drain plug. See Figures 47 and 48 starting on page 20. Afterward, continue reading instructions below. 6. Tip engine to position the oil drain plug at the lowest point on the engine (see equipment manufacturer’s instructions). 7. Remove oil drain plug and drain oil into an approved recyclable oil container. NOTE Used oil must be disposed of at a proper collection center. 8. Install oil drain plug and tighten securely. See Figure 48. 9. Remove oil fill cap/plug from oil fill hole. • See Figures 47 and 48 starting on page 20. Afterward, continue reading instructions below. • See "III. Oil and Fuel Specifications" instructions on page 4. Afterward, continue reading instructions below. • See Table 1 on page 4. Afterward, continue reading instructions below. 10. Add oil to overflow point, making sure to avoid spilling and fill with recommended oil. NOTES DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. Contact your Authorized Tecumseh Servicing Dealer for Tecumseh Oil. 11. Wipe away any spilled oil. 12. Screw oil fill cap/plug back into oil fill hole. Tighten securely. See Figures 47 and 48 starting on page 20. Afterward, continue reading instructions below. 13. Carefully disconnect spark plug wire from grounding post, if provided. See Figure 49. See "G. Avoid Accidental Starts" instructions on page 2. Afterward, continue reading instructions below. 14. Carefully re-connect spark plug wire to spark plug. See Figure 50. C. Spark Plug Check spark plug yearly or every 100 operating hours. 1. Clean area around spark plug. 2. Remove and inspect spark plug. 3. Replace spark plug if porcelain is cracked or if electrodes are: •Pitted • Burned • Fouled with Deposits 4. Check electrode gap with wire feeler gauge and set gap to—.030 in. (0.76mm) if necessary. See Figure 51. 5. Install spark plug and tighten securely. 1 2 1. Oil Fill Cap/Plug 2. Oil Drain Plug Figure 48. Oil Fill Cap/Plug and Oil Drain Plug Figure 49. Disconnecting/Connecting Spark Plug Figure 50. Typical Spark Plug Connection Figure 51. Resistor Spark Plug 1. .030 in. (0.76mm) Gap 2. Electrodes 3. Porcelain 12 3 NOTE A resistor spark plug must be used for replacement. Contact your Authorized Tecumseh Servicing Dealer for a Tecumseh Resistor Spark Plug. 181-1275-14 4-Cycle • Snow King Engine Page 21 D. Adjustments DO NOT make any engine adjustments. Factory settings are satisfactory for most conditions. If adjustments are needed, contact your Authorized Tecumseh Servicing Dealer. E. Carburetor If you think your carburetor needs adjusting, see your nearest Authorized Tecumseh Servicing Dealer. Engine performance should NOT be affected at altitudes up to 7,000 feet (2,134 meters). For operation at higher elevations, contact your Authorized Tecumseh Servicing Dealer. F. Alternator (Optional) For alternator related electrical problems such as: • Inoperative Starter • Discharged Battery • Fuse Replacement • Alternator Maintenance/Repairs See your equipment manufacturer’s instructions and an Authorized Tecumseh Servicing Dealer. G. Engine Speed !WARNING To avoid serious injury or death, DO NOT modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. NEVER tamper with factory setting of engine governor. Running the engine faster than the speed set at the factory can be dangerous and will VOID THE ENGINE WARRANTY. H. Removing Snow from Engine After each use, remove snow from the following areas: • Oil Fill Cap/Dipstick • Fuel Fill Cap • Recoil Starter/Flywheel Screen • Linkage •Guards • Spark Plug Connection (If visible). • Electric Starter Switch Box, if present (see equipment manufacturer’s instructions). See "A. Engines with Electric Starters" instructions on page 10. Afterward, continue reading instructions below. NOTE See equipment manufacturer’s instructions for proper location of fuel fill cap and control lever. Removing snow will ease operati...
Эта инструкция также подходит к моделям:Снегоочистители - SNOW KING LH195SA (1.84 mb)
Снегоочистители - SNOW KING LH195SA (1.84 mb)
Снегоочистители - SNOW KING LH195SP (1.84 mb)
Снегоочистители - SNOW KING LH318SA (1.84 mb)