Оценок - 3, средний балл: 3 ( )

Производитель: Buhler Размер: 1.84 mb Название файла: Язык инструкции:

See Figure 7. • Be sure oil fill cap/dipstick or oil fill cap/plug is tightened securely. NOTES DO NOT overfill oil filler. Doing so may result in oil carryover to the equipment and cause malfunction or damage. DO NOT allow oil level to fall below the “ADD” mark on oil fill cap/dipstick. Doing so may result in equipment malfunction or damage. Contact your Authorized Tecumseh Servicing Dealer for Tecumseh Oil. Some engines are equipped with a oil fill cap/dipstick or oil fill cap/plug (see equipment manufacturer’s instructions). To change the oil on your engine, see "B. Changing Oil" instructions on page 17. Table 1. Recommended Oil -20 FO 32 FO32 FO 40 FO-20 CO 20 FO 40 CO30 CO20 CO10 CO0 CO-10 CO-30 CO 0 FO 60 FO 80 FO 100 FOStraight Grade 730225A or SAE 30 Tecumseh Part No. Multi Grade 730226A or SAE 5W30 or SAE 10 Tecumseh Part No. Synthetic 730263 or SAE 0W30 Tecumseh Part No. Tecumseh Recommended Oil Usage Table 2. Oil Sump Capacity Oil Sump Capacity Engine Ounces U.S. Pints Liters Model Number 21 1-1/4 .62 LH195SA/LH195SP OH195SA/OH195SP 26 1-5/8 .77 LH318SA/LH358SA OH318SA 28 1-3/4 .83 OH358SA Table 3. Recommended Fuel Fuel Component Percentage Ethanol 10% Grain Alcohol (“Gasohol”) 10% MTBE (Methyl Tertiary Butyl Ether) 15% ETBE (Ethyl Tertiary Butyl Ether) 15% FULLADDOK Fill Between “FULL” and “ADD” Marks Figure 7. Engine Oil Level Page 4 4-Cycle • Snow King Engine 181-1275-14 181-1275-14 4-Cycle • Snow King Engine Page 5 B. Filling Oil Sump I. Oil Fill Cap/Dipstick If your engine has an oil fill cap/dipstick go to step 1. If your engine does NOT have an oil fill cap/dipstick, see "II. Oil Fill Cap/Plug" instructions below. 1. Be sure engine is upright and level. 2. Unscrew oil fill cap/dipstick from oil filler tube and wipe dipstick clean. See Figures 8 and 9. 3. Screw oil fill cap/dipstick back into oil filler tube. Tighten securely. 4. Unscrew and remove oil fill cap/dipstick from oil filler tube. Note oil level. If oil reading on dipstick is below “ADD” mark, slowly add oil to reach “FULL” level. See Figure 7 on page 4. Afterward, continue reading instructions below. 5. Screw oil fill cap/dipstick back into oil filler tube. Tighten securely. 6. Wipe away any spilled oil. NOTE To change oil for engines with an oil fill cap/dipstick, see "B. Changing Oil" instructions on page 17. II. Oil Fill Cap/Plug If your engine does NOT have an oil fill cap/dipstick, go to step 1. If your engine has an oil fill cap/dipstick, see "I. Oil Fill Cap/Dipstick" instructions above. 1. Be sure engine is upright and level. 2. Clean area around oil fill cap/plug. See Figure 9. 3. Unscrew oil fill cap/plug. 4. Add oil to overflow point, making sure to avoid spilling. 5. Screw oil fill cap/plug back into oil fill hole. Tighten securely. 6. Wipe away any spilled oil. NOTE To change oil for engines with an oil fill cap/plug, see "B. Changing Oil" instructions on page 17. Figure 8. Oil Fill Cap/Dipstick Locations Figure 9. Oil Fill/Drain Locations OH318SA/OH358SA OH195SA/OH195SP LH195SA/LH195SP LH318SA/LH358SA STOP STOP 1. Oil Fill Cap/Dipstick 2. Oil Fill Cap/Plug 3. Oil Drain Plug 1 3 2 3 Back View 2 3 3 Angled Front View C. Check the Following Items NOTE Be sure equipment is in neutral before attempting to start (see equipment manufacturer’s instructions). 1. Be sure ignition switch on engine or equipment is in “ON”, “RUN” or “START” position. See Figures 10, 11 and 12. Or Ignition key, if present (see equipment manufacturer’s Figure 10. Ignition Key instructions), is inserted into ignition key slot in carburetor cover. DO NOT turn ignition key. Be sure ignition key snaps into place. See Figures 10 and 11. 2. Be sure fuel valve, if present (see equipment manufacturer’s instructions) is open. See Figure 13. 3. Check engine and equipment before each operation for loose nuts, bolts and attachments; keep these items tightened. D. Check the Item Descriptions The item descriptions listed below are for all 4-Cycle Horizontal Crankshaft Snow King Engine Models. See Figure 14 on page 7. 1. Control Lever 2. Oil Drain Plug 3. Choke 4. Ignition Key or Ignition Switch 5. Carburetor Cover 6. Muffler With Muffler Guard 7. Oil Fill Cap/Dipstick 8. Spark Plug Cap 9. Fuel Fill Cap 10. Starter Cord Handle 11. Fuel Valve 12. Primer Bulb 13. Recoil Starter/Flywheel Guard Figure 12. Typical Engine Symbols Figure 11. Possible Ignition Key Locations STOPSTOPSTOPSTOPSTOP STOPSTOP SLOW RUN FAST CHOKE PRIMER Fuel Valve “OPEN” Position Shown Fuel Tank Turn Valve Clockwise To “OFF” Position Figure 13. ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: