Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
4. To adjust the position of the chute wheel assembly, loosen the clamp screw 2–3 turns and reposition the chute wheel assembly by sliding it backwards or forwards. 5. Retighten the clamp screw when the chute wheel assembly is repositioned. Operation of the blower vac Prior to using the blower vac, ensure you have read and understood this instruction manual. Ensure you are wearing suitable clothing and also safety equipment like safety glasses, ear protection and a mask if necessary. Ensure the attachments to the blower vac are correctly fitted and adjusted. Be aware of other people and animals in the area where you are to be operating the blower vac. To turn the blower vac on 1. Check the on/off switch is in the off position. This is where the slide switch is in the back position and the letter “O” is displayed towards the front of the slide switch. 2. Plug the power cord into an approved electrical extension cord, and turn the extension cord on. 3. Ensuring the blower vac is directed in a safe direction, push the on/off switch forward and the blower vac will start. The letter “I” will be displayed on the rear section of the slide switch when the switch is in the “on” position. Be sure to be holding the blower vac firmly on start up. 9 While in the “on” position, the blower vac will continue to operate without the need to hold the switch in the “on” position. To turn the blower vac off To turn the blower vac “off”, slide the on/off switch backward and this will turn the blower vac off. In the off position the letter “O” will be displayed towards the front of the switch. Important. After you have turned the blower vac off, do not leave the product until the blower vac has been fully disconnected from the electrical supply. Extension cord support During use of the blower vac, the extension cord will continually be pulled as you move from one area to another. An extension cord support has been provided on the housing of the blower vac to assist in preventing the electrical connection between the extension cord and blower vac plug being forced apart. Note. The support is for the extension cord, and not the cable from the blower vac. 1. To fit the extension cord to the support, make a tight loop in the extension cord, approximately 300mm from the socket on the extension cord. 2. Fit the loop into the square recess in the back portion of the blower vac on the right hand side. 3. Push the loop all the way through the housing by approximately 25mm. 4. Push each side of the loop downwards so each side of the loop fits into the round cut away section. 5. To seat the cable firmly, gently pull one of the two lengths of extension cable on the right hand side of the blower vac. 6. After, and only after the cable is correctly seated, plug the blower vac plug into the socket of the extension cable. To select the blow operation 1. Move the selector lever towards the back of the housing. When the blow operation is selected, air is drawn up through the large blow/vac tube and then expelled at a much higher velocity in the lower cavity below the blow/vac tube. Ensure when the blow operation is selected the blower vac is pointed, directed and used in a safe manner. Do not direct the air flow from this blower vac directly or indirectly towards another person. To select the vacuum operation 1. Push the selector lever forward. When the vacuum operation is selected, air and debris is drawn up through the large vac tube, and forced through the mulching impellor. The debris is mulched and then blown down into the collection bag. Important. Always ensure the collection bag is correctly attached as per the “Fitting the collection bag” section in this manual. Always be aware of what is being drawn up into the blow/vac tube. This product is only designed for garden debris like leaves, twigs and garden cuttings. 10 Important notes when using the blower/ vacuum selector lever Do not force the lever. The lever should move with very little resistance. If the lever is difficult to move, disconnect the power supply, remove the collection bag and ensure debris, dirt or mud has not jammed the lever inside the large round outlet. When selecting either of the operations, ensure the selector lever is fully in one position or the other, not half way. To empty the collection bag The collection bag is attached to the blower vac in 3 places. It is not necessary to remove the collection bag from the blower vac when the bag needs to be emptied. The rear of the bag is fitted with a full length zip. Simply open the zip and empty the contents. Ensure to close the zip prior to operating the blower vac. Tips for using your blower vac The following points may assist you in the operation of the blower vac. • Always try and vacuum dry leaves, cuttings or general garden debris. • Wet material is difficult to mulch and also can cause the blower vac to clog. • If the leaves etc. are damp, then use the blower vac in blow selection to pile the leaves etc. into one a...
Эта инструкция также подходит к моделям:Системы вентиляции - ST1800 (285.02 kb)