Nonslip footwear isrecommended. Wear protective hair covering to containlong hair. 4. DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wetlocations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placingarms, hands, and fingers in danger. 5. M A I N TAIN A L L TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accesso

When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersizedcord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. C shows the correct gauge touse depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavierthe cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STAT I O N A RY ELECTRIC MACHINES A m p e re R a t i n g Vo l t s Total Length of Cor

#JB11085 printEd in taiWan .........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

-30 G0449/G0450 37" Drum Sander To adjust V-belt tension: 1. Disconnect power to the sander! 2. Open the side cover. 3. Turn the motor mount nuts in the direction shown in Figure 30 to loosen or tighten the V-belts. - - - - Pulley Alignment Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplaner) for optimum performance. Each pulley can be adjusted by loosening the set screw that secures the pu

4. Motor overloaded. 1. Repair or replace connections on motor for loose or shorted terminals or worn insulation. 2. Correct the low voltage conditions. 3. Install correct fuses or circuit breakers. 4. Reduce load on motor. Drums run backwards (G0450 only). 1. Two of the power wires are reversed (G0450 only). 1. Switch two of the current carrying wires at the main power block (G0450 only). Machine slows when sanding, making a squealing noise, especially on start-up. 1. V-belts loose. 2. V-belts

WASHR 3/8 (G0582/G0445) 5318 P05825318 HANDLE (G0582/G0445) 5319 PSS08 SET SCREW 5/16-18 X 1/2 5320 P05825320 ADJUSTMENT RING (G0582/G0445) 5321 PB03 HEX BOLT 5/16-18 X 1 (G0582/G0445) 5322 PW07 FLAT WASHER 5/16 (G0582/G0445) 5323 P05825323 HANDLE (G0582/G0445) 5401 P05825401 HOUSING (G0582/G0445) 5401 P9962Z5401 HOUSING (G9962Z/G9962ZX) 5402 P05825402 ROLLER (G0582/G0445) 5402 P9962Z5402 ROLLER (G9962Z/G9962ZX) 5403 P9962Z5403 FASTENING TUBE 5405 P05825405 PULLEY (G0582/G0445) 5405

Keep loose clothing rolled up and long hair tied up and away from machinery. Table Movement Adjusting Feed Rate T able height can be adjusted manually or with the digital key pad and motor (see Figure 15). Manual Table Movement: Turn the handwheel located under the front of the infeed table for manual table positioning. Motorized Table Movement: Press the TABLE UP or TABLE DOWN key once for motorized table positioning in 0.005" (0.1mm) increments. Numerical Key Pad: Push the keys to enter

3. Replace conveyor belt. Straight strip of notches on workpiece. 1. Pressure rollers are dirty or damaged. 1. Clean or repair pressure rollers. Awarning For your safety, turn the power switch off and disconnect the sander from the power source and the air supply before starting the applicable troubleshooting. -40- o G0445/G0582/G9962Z/9962ZX Wide Belt Sander Troubleshooting SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Snake shaped marks on workpiece. 1. Sanding belt damaged or dirty. 1. Cl

Improper oscillation. To check the sanding belt oscillation: 1. Be sure the sanding belt is properly installed and the belt tension knob and air supply are ON. 2. Turn ON the sanding belt. —If the belt oscillates without contacting the limit switches, but the oscillation time to the left and right are NOT equal, proceed to Step 7, on Page 31. 3. An adequate stream of air through the air fork gap (Figure 26) is essential for proper oscillation. If the jet of air is weak through the gap, the

They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Introduction The MS2000 is a complete sanding kit that allows you to choose between 4 different sanding configurations to do a variety of tasks. Combining the versatility with the Sm