INSTALLING THE DISC SANDER TABLE 1. Thread an M8 x 1.25 x 20mm hex socket head screw (A) Fig. 10 partially into the hole in the base of the sander. Insert the rod (B) into the hole. Align the flat of the rod (B) with the screw (A). Tighten the screw (A). 2. Slide the table assembly (C) Fig. 11 on the rod (B). 3. Thread an M8 x 1.25 x 20mm hex socket head screw (A) Fig. 11 into the hole in the table support bracket. Align the flat on the rod (B) with the screw (A). Tighten the screw (A). Fig. 10

This means that it is constructed throughout with TWO separate “layers” of electrical insulation or one DOUBLE thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your Drill is equipped with a two-prong plug which permits you to use extension cords without concern for maintaining a ground connection. NOTE DOUBLE-INSULATION does not take the place of normal safety precautions when operating t

They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. Introduction The MS2000 is a complete sanding kit that allows you to choose between 4 different sanding configurations to do a variety of tasks. Combining the versatility with the Sm

The following grinders and sanders are described in this manual. D28474 D28493 D28494 D28497 D28499 7" Angle Grinder 8,000 rpm 9" Angle Grinder 5,000 rpm 7"/9" Angle Grinder 6,000 rpm 7"/9" Angle Sander 6,000 rpm 7"/9" Angle Grinder 6,000 rpm Components A. Trigger Switch C. Spindle Lock E. Spindle G. Rubber Bumper A B D E F C G Features SWITCH B. Lock On Button D. Side Handle F. Soft Mount The tool is controlled by a trigger switch (A). A lock-on button (B) provides increased comfort in extended

Spindle Lock Button TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. (See Figure 1) In order to prevent the spindle of the tool from rotating while installing or removing accessories, a spindle lock button has been provided in the gear head of the machine. To lock the spindle, depress and hold the lock button. NEVER DEPRESS THE SPINDLE LOCK BUTTON WITH THE TOOL RUNNING OR COASTING. Attaching and Removing Polishing Pads (FIGURES 4 & 5) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. To attach pad,

6. REMOVE adjusting keys or blade wrenches before turning a tool "ON". A wrench that is left attached to a rotating part of a tool may result in personal injury. 7. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 8. ALWAYS SECURE YOUR WORK. Use clamps or a vise to hold work when practical. It issafer than usingyour hand and frees both hands to operate tool. 9. USE SAFETY EQUIPMENT. Always wear

Copyright© 2004 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call 1-800-444-3353. PRODUCT SPECIFICATIONS Item Description Orbits Per Minute 10,000 Orbital Motion 5/32 " Diameter Operating PSI 90 PSI Air Consumption 4.5 CFM @ 90 PSI (No Load) Pad Thread Size 5/16 " x 24 Pad and Sanding

Mount wheel on a rod or pencil through arbor hole and tap the side of the grinding wheel (in the positions shown in Figure 4) with a light, non-metallic implement such as the handle of a screwdriver. A sound and undamaged wheel will give a clear tone. If cracked, there will be a dead or dull sound and not a clear ring. If damaged, the wheel should not be used. 7. As the grinding wheel diameter decreases with use, the position of the work rest should be adjusted. Optimally, the distance between t

Do not remove the disc flange. OPERATION • Make sure the flats on the bottom of the disc flange are engaged with the flats on the spindle. • Place the grinding wheel over the spindle. • Thread the clamp nut on the spindle with the flat side of the nut facing up. • Fit the raised, small diameter portion of the clamp nut into the hole in the wheel and finger tighten. WARNING: Always install a grinding wheel with the depressed center against the disc flange. Failure to do so will cause the grinding

Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANTPlease make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. Part No. 902388 - 02-21-02 MODEL 7406 ESPANOL: PAGINA 13 FRANCAISE : PAGE 27 To learn more about Porter-Cable visit our webs