Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersizedcord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. C shows the correct gauge touse depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavierthe cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STAT I O N A RY ELECTRIC MACHINES A m p e re R a t i n g Vo l t s Total Length of Cord in Feet Gauge of Extension Cord 0 - 6 1 2 0 up to 2 5 18 AW G 0 - 6 1 2 0 2 5 - 5 0 16 AW G 0 - 6 1 2 0 5 0 - 1 0 0 16 AW G 0 - 6 1 2 0 1 0 0 - 1 5 0 14 AW G 6 - 1 0 1 2 0 up to 2 5 18 AW G 6 - 1 0 1 2 0 2 5 - 5 0 16 AW G 6 - 1 0 1 2 0 5 0 - 1 0 0 14 AW G 6 - 1 0 1 2 0 1 0 0 - 1 5 0 12 AWG 1 0 - 1 2 1 2 0 up to 2 5 16 AW G 1 0 - 1 2 1 2 0 2 5 - 5 0 16 AW G 1 0 - 1 2 1 2 0 5 0 - 1 0 0 14 AW G 1 0 - 1 2 1 2 0 1 0 0 - 1 5 0 12 AW G 1 2 - 1 6 1 2 - 1 6 1 2 - 1 6 1 2 0 1 2 0 1 2 0 up to 2 5 2 5 - 5 0 14 AW G 12 AW G GREATER THAN 50 FEET NOT RECOMMENDED Fig. C FUNCTIONAL DESCRIPTION F O R E W O R D The ShopMaster Model SM500 is a 4" Belt, 6" Disc Sander that comes equipped with a 5.2 AMP 120 Volt Single PhaseInduction Motor, a tilting table, a miter gauge, a backstop, a 4" x 36" 60-grit sanding belt, and a 6" 60-grit sanding disc. You can mount the tilting table for use on either the belt or disc unit, and can operate the belt in the horizontal position, the vertical position, or any position in between. NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in themanual are representative only and may not depict the actual color, labeling, or accessories, and are intended toillustrate technique only. 7 C A RTON CONTENTS 1 2 3 4 8 7 10 6 5 9 11 12 13 14 15 16 17 18 1. Motor and Base 11. 1/8" Hex Wrench 2. Disc Table 12. 6mm Hex Wrench 3. Belt and Pulley Guard 13. M8 x 1.25 x 20mm Hex Socket Head Screw (3) 4. Disc Plate 14. M6 x 1 x 30mm Cheese Head Screws (2) 5. Dust Chute 15. 1/4-20 x 1/2" Hex Head Screw (1) 6. Support Rod 16. M5 x .08 x 10mm Pan Head Screw w/washer (3) 7. Lower Disc Guard 17. M4 x .7 x 12mm Sheet Metal Screw (3) 8. Sanding Disc 18. 5/16" Flat Washer (1) 9. Backstop 10. Miter Gauge U N PACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. 8 A S S E M B LY D B E C A Fig. 1 Fig. 2 F G For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. A S S E M B LY TOOLS REQUIRED 1/8" Hex Wrench (Supplied) Phillips Screwdriver 6 mm Hex Wrench (Supplied) Adjustable Wrench A S S E M B LY TIME ESTIMAT E Less than one hour ADJUSTING THE BELT TENSION Your sander was shipped from the factory with the drive belt (A) Fig. 1 attached to both pulleys (B) and (C). Beforeassembling the machine, check and adjust the belt tension. 1. Loosen the screw (D) Fig. 1 with the 6mm hex wrench, and move the sanding arm (E) to the vertical position toexpose belt tensioning screw (F) Fig. 2, and locknut (G). 2. Check the belt tension by applying light pressure onthe belt halfway between the two pulleys.The belt hasthe correct tension when you can deflect it approximately 1/4". NOTE: The belt does not require excessive tension tofunction properly. 3. To adjust, loosen the locknut (A) Fig. 3, and tighten orloosen the adjusting screw (B) with the supplied 6mmhex wrench until the belt has the correct tension. 4. Tighten locknut (A). 5. Move the sanding arm to the horizontal position. Fig. 3 A B 9 ATTACHING THE BELT AND PULLEY GUARD Attach the belt and pulley guard (A) Fig. 4 to the machinebase using the two M6x1x30mm cheese head screws(B). INSTALLING THE SANDING DISC PLATE 1. Turn the 1/4-20 x 1/4" hex socket set screw (A) Fig. 5 counter-clockwise until it clears the hole (B) in thesanding plate. 2. Align the flat of the drive shaft with the set screw (A) Fig. 6 in the hub of the plate (B) and install thesanding disc plate (B) on the drive shaft. Slide theplate (B) on the shaft (C) until the plate surface andthe shaft are flush. Note: Do not allow the shaft to extend past the surfaceof the plate. 3. Use the supplied 1/8" hex wrench (A) Fig. 7 totighten the set screw, located in the slot in the backof belt and pulley guard. Fig. 4 B A A B Fig. 5 Fig. 6 Fig. 7 A B C A 10 ATTACHING THE SANDING DISC 1. Clean the sanding disc plate (A) Fig. 8. 2. Peel the backing from sanding disc and press thedisc (B) firmly into position all the way around thesanding plate (Fig. 8). B A Fig. 8 ATTACHING THE LOWER COVER FOR THE SANDING DISC Install the lower cover (...
Эта инструкция также подходит к моделям:Шлифовальные станки - ShopMaster SM500 (20.09 mb)